Power cycling is the act of turning a piece of equipment, usually a computer, off and then on again. Reasons for power cycling include having an electronic device reinitialize its set of configuration parameters or recover from an unresponsive state of its mission critical functionality, such as in a crash or hang situation. Power cycling can also be used to reset network activity inside a modem. It can also be among the first steps for troubleshooting an issue. == Overview == Power cycling can be done manually, usually using the power switch on the device, or remotely, through some type of external device connected to the power input. In the data center environment, remote control power cycling can usually be done through a power distribution unit, over the network. In the home environment, this can be done through home automation powerline communications. Most Internet service providers publish a "how-to" on their website showing their customers the correct procedure to power cycle their devices. Power cycling is a common diagnostic procedure usually performed first when a computer system freezes. However, frequently power cycling a computer can cause thermal stress. Reset has an equal effect on the software but may be less problematic for the hardware as power is not interrupted. == Historical uses == On all Apollo missions to the moon, the landing radar was required to acquire the surface before a landing could be attempted. But on Apollo 14, the landing radar was unable to lock on. Mission control told the astronauts to cycle the power. They did, the radar locked on just in time, and the landing was completed. During the Rosetta mission to comet 67P/Churyumov–Gerasimenko, the Philae lander did not return the expected telemetry on awakening after arrival at the comet. The problem was diagnosed as "somehow a glitch in the electronics", engineers cycled the power, and the lander awoke correctly. During the launch of the billion dollar AEHF-6 satellite on 26 March 2020 by an Atlas V rocket from Cape Canaveral Space Force Station in Florida, a hold was called at T-46 seconds due to hydraulic system not responding as expected. The launch crew turned it off and back on, and the launch proceeded normally. In 2023 the Interstellar Boundary Explorer spacecraft stopped responding to commands after an anomaly. When gentler techniques failed, NASA resorted to rebooting the spacecraft with the remote equivalent of a power cycle.
Circle Hough Transform
The circle Hough Transform (CHT) is a basic feature extraction technique used in digital image processing for detecting circles in imperfect images. The circle candidates are produced by “voting” in the Hough parameter space and then selecting local maxima in an accumulator matrix. It is a specialization of the Hough transform. == Theory == In a two-dimensional space, a circle can be described by: ( x − a ) 2 + ( y − b ) 2 = r 2 ( 1 ) {\displaystyle \left(x-a\right)^{2}+\left(y-b\right)^{2}=r^{2}\ \ \ \ \ (1)} where (a,b) is the center of the circle, and r is the radius. If a 2D point (x,y) is fixed, then the parameters can be found according to (1). The parameter space would be three dimensional, (a, b, r). And all the parameters that satisfy (x, y) would lie on the surface of an inverted right-angled cone whose apex is at (x, y, 0). In the 3D space, the circle parameters can be identified by the intersection of many conic surfaces that are defined by points on the 2D circle. This process can be divided into two stages. The first stage is fixing radius then find the optimal center of circles in a 2D parameter space. The second stage is to find the optimal radius in a one dimensional parameter space. === Find parameters with known radius R === If the radius is fixed, then the parameter space would be reduced to 2D (the position of the circle center). For each point (x, y) on the original circle, it can define a circle centered at (x, y) with radius R according to (1). The intersection point of all such circles in the parameter space would be corresponding to the center point of the original circle. Consider 4 points on a circle in the original image (left). The circle Hough transform is shown in the right. Note that the radius is assumed to be known. For each (x,y) of the four points (white points) in the original image, it can define a circle in the Hough parameter space centered at (x, y) with radius r. An accumulator matrix is used for tracking the intersection point. In the parameter space, the voting number of those points that have a newly defined circle passing through them would be increased by one for every circle. Then the local maxima point (the red point in the center in the right figure) can be found. The position (a, b) of the maxima would be the center of the original circle. === Multiple circles with known radius R === Multiple circles with same radius can be found with the same technique. Note that, in the accumulator matrix (right fig), there would be at least 3 local maxima points. === Accumulator matrix and voting === In practice, an accumulator matrix is introduced to find the intersection point in the parameter space. First, we need to divide the parameter space into “buckets” using a grid and produce an accumulator matrix according to the grid. The element in the accumulator matrix denotes the number of “circles” in the parameter space that are passing through the corresponding grid cell in the parameter space. The number is also called “voting number”. Initially, every element in the matrix is zeros. Then for each “edge” point in the original space, we can formulate a circle in the parameter space and increase the voting number of the grid cell which the circle passes through. This process is called “voting”. After voting, we can find local maxima in the accumulator matrix. The positions of the local maxima are corresponding to the circle centers in the original space. === Find circle parameter with unknown radius === Since the parameter space is 3D, the accumulator matrix would be 3D, too. We can iterate through possible radii; for each radius, we use the previous technique. Finally, find the local maxima in the 3D accumulator matrix. Accumulator array should be A[x,y,r] in the 3D space. Voting should be for each pixels, radius and theta A[x,y,r] += 1 The algorithm : For each A[a,b,r] = 0; Process the filtering algorithm on image Gaussian Blurring, convert the image to grayscale ( grayScaling), make Canny operator, The Canny operator gives the edges on image. Vote on all possible circles in accumulator. The local maximum voted circles of Accumulator A gives the circle Hough space. The maximum voted circle of Accumulator gives the circle. The Incrementing for Best Candidate : For each A[a,b,r] = 0; // fill with zeroes initially, instantiate 3D matrix For each cell(x,y) For each theta t = 0 to 360 // the possible theta 0 to 360 b = y – r sin(t PI / 180); //polar coordinate for center (convert to radians) a = x – r cos(t PI / 180); //polar coordinate for center (convert to radians) A[a,b,r] +=1; //voting end end == Examples == === Find circles in a shoe-print === The original picture (right) is first turned into a binary image (left) using a threshold and Gaussian filter. Then edges (mid) are found from it using canny edge detection. After this, all the edge points are used by the Circle Hough Transform to find underlying circle structure. == Limitations == Since the parameter space of the CHT is three dimensional, it may require lots of storage and computation. Choosing a bigger grid size can ameliorate this problem. However, choosing an appropriate grid size is difficult. Since too coarse a grid can lead to large values of the vote being obtained falsely because many quite different structures correspond to a single bucket. Too fine a grid can lead to structures not being found because votes resulting from tokens that are not exactly aligned end up in different buckets, and no bucket has a large vote. Also, the CHT is not very robust to noise. == Extensions == === Adaptive Hough Transform === J. Illingworth and J. Kittler introduced this method for implementing Hough Transform efficiently. The AHT uses a small accumulator array and the idea of a flexible iterative "coarse to fine" accumulation and search strategy to identify significant peaks in the Hough parameter spaces. This method is substantially superior to the standard Hough Transform implementation in both storage and computational requirements. == Application == === People Counting === Since the head would be similar to a circle in an image, CHT can be used for detecting heads in a picture, so as to count the number of persons in the image. === Brain Aneurysm Detection === Modified Hough Circle Transform (MHCT) is used on the image extracted from Digital Subtraction Angiogram (DSA) to detect and classify aneurysms type. == Implementation code == Circle Detection via Standard Hough Transform, by Amin Sarafraz, Mathworks (File Exchange) Hough Circle Transform, OpenCV-Python Tutorials (archived version on archive.org)
Subpixel rendering
Subpixel rendering is a method used to increase the effective resolution of a color display device. It utilizes the composition of each pixel, which consists of three subpixels of which are red, green, and blue that can each be individually addressable on the display matrix. Subpixel rendering is primarily used for text rendering on standard DPI displays. Despite the inherent color anomalies, it can also be used to render general graphics. == History == The origin of subpixel rendering as used today remains controversial. Apple Inc., IBM, and Microsoft patented various implementations that differed in technical details owing to the different purposes for which their technologies were intended. Microsoft held several patents in the United States for subpixel rendering technology used in text rendering on RGB Stripe layouts. The patents 6,219,025; 6,239,783; 6,307,566; 6,225,973; 6,243,070; 6,393,145; 6,421,054; 6,282,327; and 6,624,828 were filed between October 7, 1998, and October 7, 1999, and expired on July 30, 2019. Analysis of the patent by FreeType indicates that the patent does not cover the idea of subpixel rendering, but rather the actual filter used as a last step to balance the color. Microsoft's patent describes the smallest possible filter that distributes each subpixel value equally among the R, G, and B pixels. Any other filter will either be blurrier or will introduce color artifacts. Apple was able to use it in Mac OS X due to a patent cross-licensing agreement. == Characteristics == A single pixel on a color display is made of several subpixels, typically three arranged left-to-right as red, green, and blue (RGB). The components are readily visible with a small magnifying glass, such as a loupe. These pixel components appear as a single color to the human eye because of blurring by optics and spatial integration by nerve cells in the eye. However, the eye is much more sensitive to the location. Therefore, turning on the G and B of one pixel and the R of the next pixel to the right will produce a white dot, but it will appear to be 1/3 of a pixel to the right of the white dot that would be seen from the RGB of only the first pixel. Subpixel rendering leverages this to provide three times the horizontal resolution of the rendered image. However, it has to blur this image to produce the correct color by ensuring the same amount of red, green, and blue are turned on as when no subpixel rendering is being done. Subpixel rendering does not necessitate the use of antialiasing. It gives a smoother result regardless of whether antialiasing is used or not since it artificially increases the resolution. However, it introduces color aliasing since subpixels are colored. Subsequent filtering applied to remove the color artifacts is a form of antialiasing, although its purpose is not smoothing jagged shapes as in conventional antialiasing. Subpixel rendering requires the software to know the layout of the subpixels. The most common reason it is wrong is monitors that can be rotated 90 (or 180) degrees, though monitors are manufactured with other arrangements of the subpixels, such as BGR or in triangles, or with 4 colors like RGBW squares. On any such display the result of incorrect subpixel rendering will be worse than if no subpixel rendering was done at all (it will not produce color artifacts, but it will produce noisy edges). == Implementations == === Apple II === Steve Gibson has claimed that the Apple II, introduced in 1977, supports an early form of subpixel rendering in its high-resolution (280×192) graphics mode. The Wozniak patent only used 2 "sub-pixels". The bytes that comprise the Apple II high-resolution screen buffer contain seven visible bits (each corresponding directly to a pixel) and a flag bit used to select between purple/green or blue/orange color sets. Each pixel, since it is represented by a single bit, is either on or off; there are no bits within the pixel itself for specifying color or brightness. Color is instead created as an artifact of the NTSC color encoding scheme, determined by horizontal position: pixels with even horizontal coordinates are always purple (or blue, if the flag bit is set), and odd pixels are always green (or orange). Two lit pixels next to each other are always white, regardless of whether the pair is even/odd or odd/even, and irrespective of the value of the flag bit. This is an approximation, but it is what most programmers of the time would have in mind while working with the Apple's high-resolution mode. Gibson's example claims that because two adjacent bits form a white block, there are, in fact, two bits per pixel: one that activates the pixel's purple left half and the other that activates its green right half. If the programmer instead activates the green right half of a pixel and the purple left half of the next pixel, the result is a white block 1/2 pixel to the right, which is indeed an instance of subpixel rendering. However, it is not clear whether any programmers of the Apple II have considered the pairs of bits as pixels—instead calling each bit a pixel. The flag bit in each byte affects color by shifting pixels half a pixel-width to the right. This half-pixel shift was exploited by some graphics software, such as HRCG (High-Resolution Character Generator), an Apple utility that displayed text using the high-resolution graphics mode, to smooth diagonals. === ClearType === Microsoft announced its subpixel rendering technology, called ClearType, at COMDEX in 1998. Microsoft published a paper in May 2000, Displaced Filtering for Patterned Displays, describing the filtering behind ClearType. It was then made available in Windows XP. Still, it was not activated by default until Windows Vista, while Windows XP OEMs could and did change the default setting. === FreeType === FreeType, the library used by most current software on the X Window System, contains two open source implementations. The original implementation uses the ClearType antialiasing filters and carries the following notice: "The colour filtering algorithm of Microsoft's ClearType technology for subpixel rendering is covered by patents; for this reason, the corresponding code in FreeType is disabled by default. Note that subpixel rendering per se is prior art; using a different colour filter thus easily circumvents Microsoft's patent claims." FreeType offers a variety of color filters. Since version 2.6.2, the default filter is light, a filter that is both normalized (value sums up to 1) and color-balanced (eliminate color fringes at the cost of resolution). Since version 2.8.1, a second implementation exists, called Harmony, that "offers high quality LCD-optimized output without resorting to ClearType techniques of resolution tripling and filtering". This is the method enabled by default. When using this method, "each color channel is generated separately after shifting the glyph outline, capitalizing on the fact that the color grids on LCD panels are shifted by a third of a pixel. This output is indistinguishable from ClearType with a light 3-tap filter." Since the Harmony method does not require additional filtering, it is not covered by the ClearType patents. === CoolType === Adobe created their own subpixel renderer called CoolType, allowing them to display documents the same way across various operating systems: Windows, MacOS, Linux etc. When it was launched around the year 2001, CoolType supported a wider range of fonts than Microsoft's ClearType, which at the time was limited to TrueType fonts. In contrast, Adobe's CoolType also supported PostScript fonts (and their OpenType equivalents). === macOS === Mac OS X (later OS X, now macOS) also used subpixel rendering, as part of Quartz 2D. However, it was removed after the introduction of Retina displays. Unlike Microsoft's implementation, which favors a tight fit to the grid (font hinting) to maximize legibility, Apple's implementation prioritizes the shape of the glyphs as set out by their designer.
ISO/IEC JTC 1/SC 24
ISO/IEC JTC 1/SC 24 Computer graphics, image processing and environmental data representation is a standardization subcommittee of the joint subcommittee ISO/IEC JTC 1 of the International Organization for Standardization (ISO) and the International Electrotechnical Commission (IEC), which develops and facilitates standards within the field of computer graphics, image processing, and environmental data representation. The international secretariat of ISO/IEC JTC 1/SC 24 is the British Standards Institute (BSI) located in the United Kingdom. == History == ISO/IEC JTC 1/SC 24 was formed in 1987 from ISO/TC 97 as a result of Resolution 21 at the ISO/IEC JTC 1 plenary. The group's origins began in computer graphics, the standardization of which was originally under ISO/IEC JTC 1/SC 21/WG 2. However, when ISO/IEC JTC 1/SC 24 was created, the standardization activity of ISO/IEC JTC 1/SC 21/WG 2 was carried over to the new subcommittee. The initial five working groups of ISO/IEC JTC 1/SC 24 were titled, “Architecture,” “Application programming interfaces,” “Metafiles and interfaces,” “Language bindings,” and “Validation, testing and registration.” The work of ISO/IEC JTC 1/SC 24 began with the Graphical Kernel System (GKS), which was adopted from ISO/IEC JTC 1/SC 21/WG 2. However, since GKS only addressed 2D functionality, attention turned to the standardization of 3D functionality. This resulted in two standards being published: GKS-3D in 1988 and PHIGS in 1989, both of which addressed 3D functionality. Since 1991, ISO/IEC JTC 1/SC 24 has held plenaries in a number of countries, including the Netherlands, Germany, United States, France, Canada, Japan, Sweden, Korea, United Kingdom, Australia, and Czech Republic. == Scope == The scope of ISO/IEC JTC 1/SC 24 is the “Standardization of interfaces for information technology based applications relating to”: Computer graphics Image processing Environmental data representation Support for the Mixed and Augmented Reality (MAR) Interaction with, and visual representation of, information Included are the following related areas: Modeling and simulation and related reference models Virtual reality with accompanying augmented reality/augmented virtuality aspects and related reference models Application program interfaces Functional specifications Representation models Interchange formats, encodings and their specifications, including metafiles Device interfaces Testing methods Registration procedures Presentation and support for creation of multimedia, hypermedia, and mixed reality documents Excluded are the following areas: Character and image coding Coding of multimedia, hypermedia, and mixed reality document interchange formats JTC 1 work in user system interfaces and document presentation ISO/TC 207 work on ISO 14000 environment management, ISO/TC 211 work on geographic information and geomatics Software environments as described by ISO/IEC JTC 1/SC 22 == Structure == ISO/IEC JTC 1/SC 24 is made up of four active working groups, each of which carries out specific tasks in standards development within the field of computer graphics, image processing and environmental data representation, together with ITU-T Study Group 16. As a response to changing standardization needs, working groups of ISO/IEC JTC 1/SC 24 can be disbanded if their area of work is no longer applicable, or established if new working areas arise. The focus of each working group is described in the group's terms of reference. Active working groups of ISO/IEC JTC 1/SC 24 are: == Collaborations == ISO/IEC JTC 1/SC 24 works in close collaboration with a number of other organizations or subcommittees, both internal and external to ISO or IEC, in order to avoid conflicting or duplicative work. Organizations internal to ISO or IEC that collaborate with or are in liaison to ISO/IEC JTC 1/SC 24 include: ISO/IEC JTC 1/WG 7, Sensor Networks ISO/IEC JTC 1/SC 29, Coding of audio, picture, multimedia and hypermedia information ISO/IEC JTC 1/SC 32, Data management and interchange ISO/TAG 14, Imagery and technology ISO/TC 130, Graphic Technology ISO/TC 184/SC 4, Industrial data ISO/TC 211, Geographic information/Geomatics ISO/TC 215, Health informatics IEC TC 100, Audio, video and multimedia system and equipment Some organizations external to ISO or IEC that collaborate with or are in liaison to ISO/IEC JTC 1/SC 24 include: Defence Geospatial Information Working Group (DGIWG) Digital Imaging and Communications in Medicine (DICOM) International Hydrographic Organization (IHO) The Khronos Group NATO - Joint Intelligence Surveillance and Reconnaissance Capability Group (JISRCG) OMG Robotics DTF Open CGM Open Geospatial Consortium (OGC) SEDRIS Organization Simulation Interoperability Standards Organization (SISO) US National Imagery Transmission Format Standard (NITFS) Technical Board (US NTB) Web3D Consortium World Intellectual Property Organization (WIPO) World Wide Web Consortium (W3C) == Member countries == Countries pay a fee to ISO to be members of subcommittees. The 11 "P" (participating) members of ISO/IEC JTC 1/SC 24 are: Australia, China, Egypt, France, India, Japan, Republic of Korea, Portugal, Russian Federation, United Kingdom, and United States. The 22 "O" (observer) members of ISO/IEC JTC 1/SC 24 are: Argentina, Austria, Belgium, Bosnia and Herzegovina, Bulgaria, Canada, Cuba, Czech Republic, Finland, Ghana, Hungary, Iceland, Indonesia, Islamic Republic of Iran, Italy, Kazakhstan, Malaysia, Poland, Romania, Serbia, Slovakia, Switzerland, and Thailand. == Published standards == ISO/IEC JTC 1/SC 24 currently has 80 published standards under their direct responsibility within the field of computer graphics, image processing, and environmental data representation, including:
Touch 'n Go eWallet
Touch 'n Go eWallet is a Malaysian digital wallet and online payment platform, established in Kuala Lumpur, Malaysia, in July 2017 as a joint venture between Touch 'n Go and Ant Financial. It allows users to make payments at over 280,000 merchant touch points via QR code, as well as perform peer-to-peer (P2P) money transfers. Since then, the e-wallet further diversified for users to pay for tolls via RFID or PayDirect, street parking and various online payment spanning e-hailing, car-sharing apps or taxis, various overhead bills; top-up for mobile prepaid or in-game currencies; purchases on e-commerce websites; food delivery; renewing motor insurance and other insurance/takaful plans; and even movie, bus, trains or airline tickets. == Background == Prior to the launch of the e-wallet service, Touch 'n Go provided stored-value physical all-in-one contactless card (namely Touch 'n Go cards or "TnG cards") that users can use to pay for toll fares, public transportation and parking lots as well as purchases in some retail stores. In 1999, Touch 'n Go also markets SmartTag devices that allow road users to pass through certain toll booths without the need to unwind the car window. The high entry cost of the device (around RM 100 each) also meant that only few can enjoy the seamless experience. In 2009, Touch 'n Go partnered with Maxis to launch FastTap, a new mobile payment service that utilised Near-Field Communication (NFC). Maxis customers can make payments by placing the phone near the card readers (that also supports physical bank cards and Touch ’N Go cards). However, the venture featured only one phone model, Nokia 6212, which greatly limited the public reach. In July 2012, Touch 'n Go announced another collaboration with CIMB and Maxis to create similar NFC-based online transaction service that runs on compatible smartphones. Touch 'n Go Wallet was launched in February 2017 as an QR code-based e-wallet application, to compete with Samsung Pay that utilizes NFC modules. In the controlled pilot test in Taman Tun Dr Ismail, the correspondents can experience basic functionalities (prepaid mobile service reload, bills payment, movie tickets and flight tickets purchase, transfer of money with another user, and payments at participating stores and restaurants). While the deployed version of the app was generally well-received, the existing process to transfer the balance to the physical TnG card stored value from the app garnered unanimous backlash. Test groups felt that the need to head to a self-service terminal named "Pick Up Device" in person within 24 hours for completion, along with the failure to do so (the balance would be credited back to the wallet after 24 hours), was not divulged clearly and also defeated the purpose of convenience, not to mention there were only 2 such terminals. The feature was eventually suspended. On 15 November 2017, Touch 'n Go was granted permission by the Central Bank of Malaysia to form a joint venture with Ant Financial, a Chinese-based financial company that operates Alipay. The partnership allowed the local e-wallet to learn from and build upon the operational model pioneered by Alipay. In June 2018, it was reported that Touch 'n Go was pilot testing the uses of the Touch 'n Go eWallet in Rapid Transit, as the ticketing system was enabled on the Kelana Jaya line in the Klang Valley. Pilot testing only applied to stations in Kelana Jaya, KL Gateway–Universiti, Kerinchi, KL Sentral, Dang Wangi, KLCC, and Ampang Park. The test was reported to be successful in February 2020 and was planned to be fully deployed on the LRT and MRT. Due to unforeseen circumstances, this feature did not come into fruition, the app merely adds in-app purchase of monthly concession cards called "My50". In August 2018, Touch 'n Go announced that selected drivers may experience first-hand a new RFID-based payment (later rebranded as "myRFID") that serves to replace SmartTag devices on closed toll roads with during pilot testing phase commencing on 3 September 2018. On 2 November 2018, participation in the ongoing pilot programme was expanded, allowing more drivers to sign up ahead of the public rollout of the RFID system. During the same period, Touch 'n Go has discontinued the sales of SmartTAG devices in favor of the RFID-based payment system. Initially, the installation of the RFID chip onto the car could only be done by Touch 'n Go staff at the RFID fitment centers, at no cost. As the pilot testing concluded on 15 February 2020, a self-installation kit are being offered to the public on Lazada and Shopee. Support for taxi-hailing mobile apps was added in November 2018 when Touch 'n Go partnered with EzCab and Public Cab, allowing users to make payments via QR code. This was later expanded to support MULA on 7 January 2020, and later MyCar on 4 April 2020. Touch 'n Go eWallet was also the first eWallet to convert Kuala Lumpur's most famous Ramadan bazaar in Kampong Bahru into "Kampong Kashless", a venue that can accept cashless QR payments. It welcomed more than 250,000 Malaysians including local celebrities and government officials. On 1 October 2019, some e-commerce websites owned by the Alibaba Group (TMall and Taobao) began to support Touch 'n Go eWallet payments, Lazada joined the list on 29 October 2019. Touch 'n Go eWallet was one of the three e-wallet services in Malaysia (the other being Boost and GrabPay) that was eligible for its users to receive an RM 30 credit in conjunction of E-Tunai Rakyat program under the Budget 2020 plan, that further normalizes adoption of cashless and mobile payment among Malaysians. Unlike Boost and GrabPay, whose P2P transfers were completely disabled until users have exhausted the RM 30 first, Touch 'n Go eWallet did not impose such measures. in 2020, Touch 'n Go eWallet joined DuitNow, an electronic transaction ecosystem in Malaysia which allows the funds from Touch 'n Go eWallet to be transferred to other competing services and vice versa, by implementing a standard DuitNow QR code deisgn. Japan become the first country outside Malaysia to support Touch 'n Go eWallet payment via Alipay Connect. During the COVID-19 pandemic and the enforcement of the movement control order, use of eWallets (including Touch 'n Go eWallet) increased tremendously among citizens due to its contactless nature of the payment and increased take-out orders at home; which in turn helped small and medium-sized enterprises to thrive. Touch 'n Go eWallet launched its loyalty programme – The Goal Hunter – in October 2020 where on monthly basis, users collect stamps by paying with the app in exchange for rewards that include lucky draws and other vouchers. == Services == Touch 'n Go eWallet app is available for download on both Google Play and Apple Appstore. It utilizes QR code technology for local in-store payments. The Touch 'n Go eWallet app also diversifies payment types, including but not limited to Utility bills Purchase of motor insurance policy Pay Later facility Prepaid reload and Postpaid payment to telecommunications companies loan repayments for courts, MBSJ payments, zakat and PTPTN payment for car parking P2P transfer airline ticket bookings; movie tickets from TGV Cinemas RFID refuelling at Shell stations (defunct after Shell launched its own payment app in 2024) User can reload the eWallet credit by setting up auto-reload, purchasing reload pins from convenience stores (such as 7-Eleven, KK Super Mart, MyNews, Family Mart etc.), reloading by FPX and credit/debit card. The PayDirect feature allows users to link their physical Touch 'n Go cards into the eWallet, where the toll fare can be debited from the eWallet balance when flashing the card near the sensor. In the circumstance of insufficient balance in the app, the toll fare will be deducted from the physical card's balance instead. This also conveniently allows users to view the card's remaining balance. Touch 'n Go eWallet is the first and only eWallet to offer a money-back guarantee when an unauthorised transaction is made on the user’s eWallet account, subject to Terms & Conditions. Payment via QR code scanning, including Touch 'n Go eWallet, becomes a norm in most of the shops/restaurants across Malaysia, including roadside hawkers/stall owners and automatic vending machines. The merchants usually display their owner's individual QR or Business account that they can apply for in-app. The popularity attributes to the low merchant onboarding cost (Unlike NFC payment and debit/credit card that requires purchase or rental of a payment terminal device at a yearly fee.) The app is also one of the few ewallet that supports bidirectional liquidity (alongside MAE developed by Maybank), where funds can be transferred two-way with bank accounts. This is not possible with the other major ewallets (GrabPay, Boost, ShopeePay etc.) where the money that is reloaded to the wallet cannot be transferred to another bank account, unless through manual req
Local-first software
Local-first software is a software engineering approach in which an application stores its data primarily on the user's own device rather than on remote servers. Users can read and write data without an Internet connection, and changes are synchronized across devices in the background when connectivity is available. The approach differs from conventional cloud-based applications, where the server holds the authoritative copy of user data and the client acts as a thin client. The term was coined in a 2019 paper published by researchers at Ink & Switch, an independent research lab, and presented at the Onward! conference at ACM SIGPLAN. The paper, sometimes referred to as a manifesto, was authored by Martin Kleppmann, Adam Wiggins, Peter van Hardenberg, and Mark McGranaghan. == Background == Before the widespread adoption of Internet-connected software in the 2000s, most desktop applications stored data as files on the user's local disk. Users had direct access to their files and could copy, back up, or delete them at will. The rise of software as a service (SaaS) and cloud-based applications like Google Docs shifted data storage to centralized servers. While cloud applications made real-time collaboration across devices straightforward, they introduced a dependency on the service provider: if the provider discontinued the service or experienced an outage, users could lose access to their data. A related concept, "offline-first," emerged in the early 2010s and focused on making web applications resilient to network interruptions. The local-first approach built on these earlier efforts while placing greater emphasis on long-term data ownership and end-to-end encryption. == Origins == === Ink & Switch manifesto === Ink & Switch is an industrial research lab co-founded by Adam Wiggins, who had earlier co-founded Heroku. Martin Kleppmann, an associate professor in the Department of Computer Science and Technology at the University of Cambridge, was a co-author of the 2019 paper. The manifesto proposed seven "ideals" for local-first software: Fast — Operations respond without network round-trips. Multi-device — Data synchronizes across a user's devices. Offline — Users can read and write data without a network connection. Collaboration — Multiple users can work on the same data concurrently. Longevity — Data remains accessible even if the software vendor ceases operation. Privacy — End-to-end encryption protects user data. User control — The vendor cannot restrict how users access or use their data. The paper surveyed existing approaches to data storage and collaboration — ranging from email attachments and Dropbox-style file synchronization to web applications and mobile backends — and argued that none of them satisfied all seven ideals simultaneously. === Role of CRDTs === The manifesto identified conflict-free replicated data types (CRDTs) as a promising technical foundation for local-first applications. CRDTs are data structures that allow multiple replicas to be edited independently and then merged without conflicts, a property first formalized in research by Marc Shapiro and colleagues around 2011. Kleppmann and collaborators at Ink & Switch developed Automerge, an open-source CRDT library for JSON documents, to make these algorithms available to application developers. == Adoption and community == Developer interest in the local-first approach grew after the 2019 paper spread on Hacker News and at developer conferences In August 2023, Wired published a feature article on the movement, describing it as an effort to reduce reliance on large cloud providers. The first Local-First Conf took place on 30 May 2024 in Berlin, with talks by Kleppmann and developers from companies including Linear and Anytype. The community has continued to expand, with regular "LoFi" meetups, a podcast (localfirst.fm), and a third edition of the conference planned for Berlin in July 2026. == Criticisms and limitations == Developers and commentators have pointed out practical difficulties with the local-first approach. Synchronizing data between multiple devices that may be offline for extended periods introduces complexity that cloud-based architectures avoid. Conflict resolution, even with CRDTs, can produce results that are technically consistent but semantically unexpected to users. Schema migrations across thousands of client devices running different application versions pose another difficulty that does not arise with server-side databases. Web browsers impose storage limits and may evict locally stored data. Safari, for instance, has been reported to clear IndexedDB data after seven days of inactivity on a given site, which undermines the assumption that local data is persistent. There is also disagreement within the local-first community about whether a fully decentralized architecture is required. The original manifesto described decentralization as the "logical end goal," but a number of products that identify as local-first still depend on centralized servers for authentication, backup, or synchronization. In a talk at Local-First Conf 2024, Kleppmann said the seven ideals are better understood as a "gradient" rather than a strict checklist.
Visual hull
A visual hull is a geometric entity created by shape-from-silhouette 3D reconstruction technique introduced by A. Laurentini. This technique assumes the foreground object in an image can be separated from the background. Under this assumption, the original image can be thresholded into a foreground/background binary image, which we call a silhouette image. The foreground mask, known as a silhouette, is the 2D projection of the corresponding 3D foreground object. Along with the camera viewing parameters, the silhouette defines a back-projected generalized cone that contains the actual object; this cone is called a silhouette cone. The intersection of the two silhouette cones defines a visual hull. which is a bounding geometry of the actual 3D object. When the reconstructed geometry is only used for rendering from a different viewpoint, the implicit reconstruction together with rendering can be done using graphics hardware. == In two dimensions == A technique used in some modern touchscreen devices employs cameras placed in the corners situated opposite infrared LEDs. The one-dimensional projection (shadow) of objects on the surface may be used to reconstruct the convex hull of the object. Visual hull generation method has also been used within experimental tele-meeting systems that aim to allow a user in a remote location to interact with virtual objects. The method uses multiple cameras to capture the real-world movements and interactions of the "sender", employing hardware-accelerated volumetric visual hull representation to create 3D volume from 2D multi-view images. Its ultimate aim is to allow 3D collaboration between the two users in the virtual realm, with the visual hull technique reducing the computational power required to allow this type of interaction and enabling the use of consumer goods such as the Wii Remote as a tool for interaction.