AI For Students Studying

AI For Students Studying — independent reviews, comparisons, pricing and step-by-step guides on Aizhi.

• 

  Automatic meter reading

  Automatic meter reading (AMR) is the technology of automatically collecting consumption, diagnostic, and status data from water meter or energy metering devices (gas, electric) and transferring that data to a central database for billing, troubleshooting, and analyzing. This technology mainly saves utility providers the expense of periodic trips to each physical location to read a meter. Another advantage is that billing can be based on near real-time consumption rather than on estimates based on past or predicted consumption. This timely information coupled with analysis can help both utility providers and customers better control the use and production of electric energy, gas usage, or water consumption. AMR technologies include handheld, mobile and network technologies based on telephony platforms (wired and wireless), radio frequency (RF), or powerline transmission. == Technologies == === Touch technology === With touch-based AMR, a meter reader carries a handheld computer or data collection device with a wand or probe. The device automatically collects the readings from a meter by touching or placing the read probe close to a reading coil enclosed in the touchpad. When a button is pressed, the probe sends an interrogate signal to the touch module to collect the meter reading. The software in the device matches the serial number to one in the route database, and saves the meter reading for later download to a billing or data collection computer. Since the meter reader still has to go to the site of the meter, this is sometimes referred to as "on-site" AMR. Another form of contact reader uses a standardized infrared port to transmit data. Protocols are standardized between manufacturers by such documents as ANSI C12.18 or IEC 61107. === AMR hosting === AMR hosting is a back-office solution which allows a user to track their electricity, water, or gas consumption over the Internet. All data is collected in near real-time, and is stored in a database by data acquisition software. The user can view the data via a web application, and can analyze the data using various online analysis tools such as charting load profiles, analyzing tariff components, and verify their utility bill. === Radio frequency network === Radio frequency based AMR can take many forms. The more common ones are handheld, mobile, satellite and fixed network solutions. There are both two-way RF systems and one-way RF systems in use that use both licensed and unlicensed RF bands. In a two-way or "wake up" system, a radio signal is normally sent to an AMR meter's unique serial number, instructing its transceiver to power-up and transmit its data. The meter transceiver and the reading transceiver both send and receive radio signals. In a one-way "bubble-up" or continuous broadcast type system, the meter transmits continuously and data is sent every few seconds. This means the reading device can be a receiver only, and the meter a transmitter only. Data travels only from the meter transmitter to the reading receiver. There are also hybrid systems that combine one-way and two-way techniques, using one-way communication for reading and two-way communication for programming functions. RF-based meter reading usually eliminates the need for the meter reader to enter the property or home, or to locate and open an underground meter pit. The utility saves money by increased speed of reading, has less liability from entering private property, and has fewer missed readings from being unable to access the meter. The technology based on RF is not readily accepted everywhere. In several Asian countries, the technology faces a barrier of regulations in place pertaining to use of the radio frequency of any radiated power. For example, in India the radio frequency which is generally in ISM band is not free to use even for low power radio of 10 mW. The majority of manufacturers of electricity meters have radio frequency devices in the frequency band of 433/868 MHz for large scale deployment in European countries. The frequency band of 2.4 GHz can be now used in India for outdoor as well as indoor applications, but few manufacturers have shown products within this frequency band. Initiatives in radio frequency AMR in such countries are being taken up with regulators wherever the cost of licensing outweighs the benefits of AMR. ==== Handheld ==== In handheld AMR, a meter reader carries a handheld computer with a built-in or attached receiver/transceiver (radio frequency or touch) to collect meter readings from an AMR capable meter. This is sometimes referred to as "walk-by" meter reading since the meter reader walks by the locations where meters are installed as they go through their meter reading route. Handheld computers may also be used to manually enter readings without the use of AMR technology as an alternate but this will not support exhaustive data which can be accurately read using the meter reading electronically. ==== Mobile ==== Mobile or "drive-by" meter reading is where a reading device is installed in a vehicle. The meter reader drives the vehicle while the reading device automatically collects the meter readings. Often, for mobile meter reading, the reading equipment includes navigational and mapping features provided by GPS and mapping software. With mobile meter reading, the reader does not normally have to read the meters in any particular route order, but just drives the service area until all meters are read. Components often consist of a laptop or proprietary computer, software, RF receiver/transceiver, and external vehicle antennas. ==== Satellite ==== Transmitters for data collection satellites can be installed in the field next to existing meters. The satellite AMR devices communicate with the meter for readings, and then sends those readings over a fixed or mobile satellite network. This network requires a clear view to the sky for the satellite transmitter/receiver, but eliminates the need to install fixed towers or send out field technicians, thereby being particularly suited for areas with low geographic meter density. ==== RF technologies commonly used for AMR ==== Narrow Band (single fixed radio frequency) Spread spectrum Direct-sequence spread spectrum (DSSS) Frequency-hopping spread spectrum (FHSS) There are also meters using AMR with RF technologies such as cellular phone data systems, Zigbee, Bluetooth, Wavenis and others. Some systems operate with U.S. Federal Communications Commission (FCC) licensed frequencies and others under FCC Part 15, which allows use of unlicensed radio frequencies. ==== Wi-Fi ==== WiSmart is a versatile platform which can be used by a variety of electrical home appliances in order to provide wireless TCP/IP communication using the 802.11 b/g protocol. Devices such as the Smart Thermostat permit a utility to lower a home's power consumption to help manage power demand. The city of Corpus Christi became one of the first cities in the United States to implement citywide Wi-Fi, which had been free until May 31, 2007, mainly to facilitate AMR after a meter reader was attacked by a dog. Today many meters are designed to transmit using Wi-Fi, even if a Wi-Fi network is not available, and they are read using a drive-by local Wi-Fi hand held receiver. The meters installed in Corpus Christi are not directly Wi-Fi enabled, but rather transmit narrow-band burst telemetry on the 460 MHz band. This narrow-band signal has much greater range than Wi-Fi, so the number of receivers required for the project are far fewer. Special receiver stations then decode the narrow-band signals and resend the data via Wi-Fi. Most of the automated utility meters installed in the Corpus Christi area are battery powered. Wi-Fi technology is unsuitable for long-term battery-powered operation. === Power line communication === PLC is a method where electronic data is transmitted over power lines back to the substation, then relayed to a central computer in the utility's main office. This would be considered a type of fixed network system—the network being the distribution network which the utility has built and maintains to deliver electric power. Such systems are primarily used for electric meter reading. Some providers have interfaced gas and water meters to feed into a PLC type system. == Brief history == In 1972, Theodore George "Ted" Paraskevakos, while working with Boeing in Huntsville, Alabama, developed a sensor monitoring system which used digital transmission for security, fire and medical alarm systems as well as meter reading capabilities for all utilities. This technology was a spin-off of the automatic telephone line identification system, now known as caller ID. In 1974, Paraskevakos was awarded a U.S. patent for this technology. In 1977, he launched Metretek, Inc., which developed and produced the first fully automated, commercially available remote meter reading and load management system. Since this system was developed pre-Internet, Metret

  Read more →
• 

  Microscope image processing

  Microscope image processing is a broad term that covers the use of digital image processing techniques to process, analyze and present images obtained from a microscope. Such processing is now commonplace in a number of diverse fields such as medicine, biological research, cancer research, drug testing, metallurgy, etc. A number of manufacturers of microscopes now specifically design in features that allow the microscopes to interface to an image processing system. == Image acquisition == Until the early 1990s, most image acquisition in video microscopy applications was typically done with an analog video camera, often simply closed circuit TV cameras. While this required the use of a frame grabber to digitize the images, video cameras provided images at full video frame rate (25-30 frames per second) allowing live video recording and processing. While the advent of solid state detectors yielded several advantages, the real-time video camera was actually superior in many respects. Today, acquisition is usually done using a CCD camera mounted in the optical path of the microscope. The camera may be full colour or monochrome. Very often, very high resolution cameras are employed to gain as much direct information as possible. Cryogenic cooling is also common, to minimise noise. Often digital cameras used for this application provide pixel intensity data to a resolution of 12-16 bits, much higher than is used in consumer imaging products. Ironically, in recent years, much effort has been put into acquiring data at video rates, or higher (25-30 frames per second or higher). What was once easy with off-the-shelf video cameras now requires special, high speed electronics to handle the vast digital data bandwidth. Higher speed acquisition allows dynamic processes to be observed in real time, or stored for later playback and analysis. Combined with the high image resolution, this approach can generate vast quantities of raw data, which can be a challenge to deal with, even with a modern computer system. While current CCD detectors allow very high image resolution, often this involves a trade-off because, for a given chip size, as the pixel count increases, the pixel size decreases. As the pixels get smaller, their well depth decreases, reducing the number of electrons that can be stored. In turn, this results in a poorer signal-to-noise ratio. For best results, one must select an appropriate sensor for a given application. Because microscope images have an intrinsic limiting resolution, it often makes little sense to use a noisy, high resolution detector for image acquisition. A more modest detector, with larger pixels, can often produce much higher quality images because of reduced noise. This is especially important in low-light applications such as fluorescence microscopy. Moreover, one must also consider the temporal resolution requirements of the application. A lower resolution detector will often have a significantly higher acquisition rate, permitting the observation of faster events. Conversely, if the observed object is motionless, one may wish to acquire images at the highest possible spatial resolution without regard to the time required to acquire a single image. == 2D image techniques == Image processing for microscopy application begins with fundamental techniques intended to most accurately reproduce the information contained in the microscopic sample. This might include adjusting the brightness and contrast of the image, averaging images to reduce image noise and correcting for illumination non-uniformities. Such processing involves only basic arithmetic operations between images (i.e. addition, subtraction, multiplication and division). The vast majority of processing done on microscope image is of this nature. Another class of common 2D operations called image convolution are often used to reduce or enhance image details. Such "blurring" and "sharpening" algorithms in most programs work by altering a pixel's value based on a weighted sum of that and the surrounding pixels (a more detailed description of kernel based convolution deserves an entry for itself) or by altering the frequency domain function of the image using Fourier Transform. Most image processing techniques are performed in the Frequency domain. Other basic two dimensional techniques include operations such as image rotation, warping, color balancing etc. At times, advanced techniques are employed with the goal of "undoing" the distortion of the optical path of the microscope, thus eliminating distortions and blurring caused by the instrumentation. This process is called deconvolution, and a variety of algorithms have been developed, some of great mathematical complexity. The end result is an image far sharper and clearer than could be obtained in the optical domain alone. This is typically a 3-dimensional operation, that analyzes a volumetric image (i.e. images taken at a variety of focal planes through the sample) and uses this data to reconstruct a more accurate 3-dimensional image. == 3D image techniques == Another common requirement is to take a series of images at a fixed position, but at different focal depths. Since most microscopic samples are essentially transparent, and the depth of field of the focused sample is exceptionally narrow, it is possible to capture images "through" a three-dimensional object using 2D equipment like confocal microscopes. Software is then able to reconstruct a 3D model of the original sample which may be manipulated appropriately. The processing turns a 2D instrument into a 3D instrument, which would not otherwise exist. In recent times this technique has led to a number of scientific discoveries in cell biology. == Analysis == Analysis of images will vary considerably according to application. Typical analysis includes determining where the edges of an object are, counting similar objects, calculating the area, perimeter length and other useful measurements of each object. A common approach is to create an image mask which only includes pixels that match certain criteria, then perform simpler scanning operations on the resulting mask. It is also possible to label objects and track their motion over a series of frames in a video sequence.

  Read more →
• 

  Biorobotics

  Biorobotics is an interdisciplinary science that combines the fields of biomedical engineering, cybernetics, and robotics to develop new technologies that integrate biology with mechanical systems to develop more efficient communication, alter genetic information, and create machines that imitate biological systems. == Cybernetics == Cybernetics focuses on the communication and system of living organisms and machines that can be applied and combined with multiple fields of study such as biology, mathematics, computer science, engineering, and much more. This discipline falls under the branch of biorobotics because of its combined field of study between biological bodies and mechanical systems. Studying these two systems allows for advanced analysis on the functions and processes of each system as well as the interactions between them. === History === Cybernetic theory is a concept that has existed for centuries, dating back to the era of Plato where he applied the term to refer to the "governance of people". The term cybernetique is seen in the mid-1800s used by physicist André-Marie Ampère. The term cybernetics was popularized in the late 1940s to refer to a discipline that touched on, but was separate, from established disciplines, such as electrical engineering, mathematics, and biology. === Science === Cybernetics is often misunderstood because of the breadth of disciplines it covers. In the early 20th century, it was coined as an interdisciplinary field of study that combines biology, science, network theory, and engineering. Today, it covers all scientific fields with system related processes. The goal of cybernetics is to analyze systems and processes of any system or systems in an attempt to make them more efficient and effective. === Applications === Cybernetics is used as an umbrella term so applications extend to all systems related scientific fields such as biology, mathematics, computer science, engineering, management, psychology, sociology, art, and more. Cybernetics is used amongst several fields to discover principles of systems, adaptation of organisms, information analysis and much more. == Genetic engineering == Genetic engineering is a field that uses advances in technology to modify biological organisms. Through different methods, scientists are able to alter the genetic material of microorganisms, plants and animals to provide them with desirable traits. For example, making plants grow bigger, better, and faster. Genetic engineering is included in biorobotics because it uses new technologies to alter biology and change an organism's DNA for their and society's benefit. === History === Although humans have modified genetic material of animals and plants through artificial selection for millennia (such as the genetic mutations that developed teosinte into corn and wolves into dogs), genetic engineering refers to the deliberate alteration or insertion of specific genes to an organism's DNA. The first successful case of genetic engineering occurred in 1973 when Herbert Boyer and Stanley Cohen were able to transfer a gene with antibiotic resistance to a bacterium. === Science === There are three main techniques used in genetic engineering: The plasmid method, the vector method and the biolistic method. ==== Plasmid method ==== This technique is used mainly for microorganisms such as bacteria. Through this method, DNA molecules called plasmids are extracted from bacteria and placed in a lab where restriction enzymes break them down. As the enzymes do this, some develop a rough edge that resembles that of a staircase which is considered 'sticky' and capable of reconnecting. These 'sticky' molecules are inserted into another bacteria where they will connect to the DNA rings with the altered genetic material. ==== Vector method ==== The vector method is considered a more precise technique than the plasmid method as it involves the transfer of a specific gene instead of a whole sequence. In the vector method, a specific gene from a DNA strand is isolated through restriction enzymes in a laboratory and is inserted into a vector. Once the vector accepts the genetic code, it is inserted into the host cell where the DNA will be transferred. ==== Biolistic method ==== The biolistic method is typically used to alter the genetic material of plants. This method embeds the desired DNA with a metallic particle such as gold or tungsten in a high speed gun. The particle is then bombarded into the plant. Due to the high velocities and the vacuum generated during bombardment, the particle is able to penetrate the cell wall and inserts the new DNA into the cell. === Applications === Genetic engineering has many uses in the fields of medicine, research and agriculture. In the medical field, genetically modified bacteria are used to produce drugs such as insulin, human growth hormones and vaccines. In research, scientists genetically modify organisms to observe physical and behavioral changes to understand the function of specific genes. In agriculture, genetic engineering is extremely important as it is used by farmers to grow crops that are resistant to herbicides and to insects such as BTCorn. == Bionics == Bionics is a medical engineering field and a branch of biorobotics consisting of electrical and mechanical systems that imitate biological systems, such as prosthetics and hearing aids. It's a portmanteau that combines biology and electronics. === History === The history of bionics goes as far back in time as ancient Egypt. A prosthetic toe made out of wood and leather was found on the foot of a mummy. The time period of the mummy corpse was estimated to be from around the fifteenth century B.C. Bionics can also be witnessed in ancient Greece and Rome. Prosthetic legs and arms were made for amputee soldiers. In the early 16th century, a French military surgeon by the name of Ambroise Pare became a pioneer in the field of bionics. He was known for making various types of upper and lower prosthetics. One of his most famous prosthetics, Le Petit Lorrain, was a mechanical hand operated by catches and springs. During the early 19th century, Alessandro Volta further progressed bionics. He set the foundation for the creation of hearing aids with his experiments. He found that electrical stimulation could restore hearing by inserting an electrical implant to the saccular nerve of a patient's ear. In 1945, the National Academy of Sciences created the Artificial Limb Program, which focused on improving prosthetics since there were a large number of World War II amputee soldiers. Since this creation, prosthetic materials, computer design methods, and surgical procedures have improved, creating modern-day bionics. === Science === ==== Prosthetics ==== The important components that make up modern-day prosthetics are the pylon, the socket, and the suspension system. The pylon is the internal frame of the prosthetic that is made up of metal rods or carbon-fiber composites. The socket is the part of the prosthetic that connects the prosthetic to the person's missing limb. The socket consists of a soft liner that makes the fit comfortable, but also snug enough to stay on the limb. The suspension system is important in keeping the prosthetic on the limb. The suspension system is usually a harness system made up of straps, belts or sleeves that are used to keep the limb attached. The operation of a prosthetic could be designed in various ways. The prosthetic could be body-powered, externally-powered, or myoelectrically powered. Body-powered prosthetics consist of cables attached to a strap or harness, which is placed on the person's functional shoulder, allowing the person to manipulate and control the prosthetic as he or she deems fit. Externally-powered prosthetics consist of motors to power the prosthetic and buttons and switches to control the prosthetic. Myoelectrically powered prosthetics are new, advanced forms of prosthetics where electrodes are placed on the muscles above the limb. The electrodes will detect the muscle contractions and send electrical signals to the prosthetic to move the prosthetic. The downside to this type of prosthetic is that if the sensors are not placed correctly on the limb then the electrical impulses will fail to move the prosthetic. TrueLimb is a specific brand of prosthetics that uses myoelectrical sensors which enable a person to have control of their bionic limb. ==== Hearing aids ==== Four major components make up the hearing aid: the microphone, the amplifier, the receiver, and the battery. The microphone takes in outside sound, turns that sound to electrical signals, and sends those signals to the amplifier. The amplifier increases the sound and sends that sound to the receiver. The receiver changes the electrical signal back into sound and sends the sound into the ear. Hair cells in the ear will sense the vibrations from the sound, convert the vibrations into nerve signals, and send it to the brain so

  Read more →
• 

  Gapo

  Gapo is a Vietnamese social networking service based in Hanoi, Vietnam. Users are able to create a personal profile and share text, photos and videos with others on the platform. Users can also use Gapo for live streaming, instant messaging, blogging, and online payments. Gapo was launched in July 2019 by Hà Trung Kiên and Duong Vi Khoa. == History == Gapo was founded in response to calls for Vietnam's Communist-led government to produce a domestic alternative to social media giants like Facebook and Google. Gapo officially launched on July 23, 2019 at an event in Hanoi. The company received 500 billion đồng (US$22 million) in funding from technology corporation G-Group to be utilized in the first phase of development. They also partnered with Sony Music Entertainment to provide music content to its services. == Features == Gapo features a news feed for posting content, livestreaming, instant messaging, and blogging. It also allows users to pay online and access public services. == Reception == Within two days of launch, Gapo received about 200,000 registrations. By September 2019, the user base increased to one million. Upon launch, Gapo experienced significant technical difficulties. Users complained about the inability to sign up for a new account and said that certain functions were not available for use at launch. This issue caused Gapo to temporarily suspend their services in order to perform upgrades and bug fixes. Gapo relaunched the next day, though many users reported that the access speed decreased. The mobile app also received mixed reviews from users in both the App Store and the Google Play Store, with an average rating of 3.1 and 3.5, respectively. Most users found the app to be a knockoff of Facebook, although some users praised the app for being locally developed. === Expert opinions on platform viability === Le Hong Hiep of the ISEAS - Yusof Ishak Institute was doubtful that a Vietnamese-owned social network service could be as powerful as a foreign-based service, stating that Vietnam might not be able to develop a viable social media network to compete with the likes of Facebook or Google. Others, like blogger Ann Chi, said that, due to local players complying with local censorship policy, there is a chance that locals might not trust Gapo and other local services in light of possible surveillance. Regarding the targeted user base figure for the end of 2019 and 2021, experts cautioned that the company might need an additional trillion đồng of funding to reach its planned user base targets. In response, the company stated that Gapo was never meant to compete with Facebook, but instead noted that the main difference between Gapo and Facebook is that Gapo provides a personalized user experience through customization. == Censorship == Gapo has the right to censor posts and news that are deemed offensive and inaccurate by users or not approved by the censorship curators.

  Read more →
• 

  Developmental robotics

  Developmental robotics (DevRob), sometimes called epigenetic robotics, is a scientific field which aims at studying the developmental mechanisms, architectures and constraints that allow lifelong and open-ended learning of new skills and new knowledge in embodied machines. As in human children, learning is expected to be cumulative and of progressively increasing complexity, and to result from self-exploration of the world in combination with social interaction. The typical methodological approach consists in starting from theories of human and animal development elaborated in fields such as developmental psychology, neuroscience, developmental and evolutionary biology, and linguistics, then to formalize and implement them in robots, sometimes exploring extensions or variants of them. The experimentation of those models in robots allows researchers to confront them with reality, and as a consequence, developmental robotics also provides feedback and novel hypotheses on theories of human and animal development. Developmental robotics is related to but differs from evolutionary robotics (ER). ER uses populations of robots that evolve over time, whereas DevRob is interested in how the organization of a single robot's control system develops through experience, over time. DevRob is also related to work done in the domains of robotics and artificial life. == Background == Can a robot learn like a child? Can it learn a variety of new skills and new knowledge unspecified at design time and in a partially unknown and changing environment? How can it discover its body and its relationships with the physical and social environment? How can its cognitive capacities continuously develop without the intervention of an engineer once it is "out of the factory"? What can it learn through natural social interactions with humans? These are the questions at the center of developmental robotics. Alan Turing, as well as a number of other pioneers of cybernetics, already formulated those questions and the general approach in 1950, but it is only since the end of the 20th century that they began to be investigated systematically. Because the concept of adaptive intelligent machines is central to developmental robotics, it has relationships with fields such as artificial intelligence, machine learning, cognitive robotics or computational neuroscience. Yet, while it may reuse some of the techniques elaborated in these fields, it differs from them from many perspectives. It differs from classical artificial intelligence because it does not assume the capability of advanced symbolic reasoning and focuses on embodied and situated sensorimotor and social skills rather than on abstract symbolic problems. It differs from cognitive robotics because it focuses on the processes that allow the formation of cognitive capabilities rather than these capabilities themselves. It differs from computational neuroscience because it focuses on functional modeling of integrated architectures of development and learning. More generally, developmental robotics is uniquely characterized by the following three features: It targets task-independent architectures and learning mechanisms, i.e. the machine/robot has to be able to learn new tasks that are unknown by the engineer; It emphasizes open-ended development and lifelong learning, i.e. the capacity of an organism to acquire continuously novel skills. This should not be understood as a capacity for learning "anything" or even “everything”, but just that the set of skills that is acquired can be infinitely extended at least in some (not all) directions; The complexity of acquired knowledge and skills shall increase (and the increase be controlled) progressively. Developmental robotics emerged at the crossroads of several research communities including embodied artificial intelligence, enactive and dynamical systems cognitive science, connectionism. Starting from the essential idea that learning and development happen as the self-organized result of the dynamical interactions among brains, bodies and their physical and social environment, and trying to understand how this self-organization can be harnessed to provide task-independent lifelong learning of skills of increasing complexity, developmental robotics strongly interacts with fields such as developmental psychology, developmental and cognitive neuroscience, developmental biology (embryology), evolutionary biology, and cognitive linguistics. As many of the theories coming from these sciences are verbal and/or descriptive, this implies a crucial formalization and computational modeling activity in developmental robotics. These computational models are then not only used as ways to explore how to build more versatile and adaptive machines but also as a way to evaluate their coherence and possibly explore alternative explanations for understanding biological development. == Research directions == === Skill domains === Due to the general approach and methodology, developmental robotics projects typically focus on having robots develop the same types of skills as human infants. A first category that is important being investigated is the acquisition of sensorimotor skills. These include the discovery of one's own body, including its structure and dynamics such as hand-eye coordination, locomotion, and interaction with objects as well as tool use, with a particular focus on the discovery and learning of affordances. A second category of skills targeted by developmental robots are social and linguistic skills: the acquisition of simple social behavioural games such as turn-taking, coordinated interaction, lexicons, syntax and grammar, and the grounding of these linguistic skills into sensorimotor skills (sometimes referred as symbol grounding). In parallel, the acquisition of associated cognitive skills are being investigated such as the emergence of the self/non-self distinction, the development of attentional capabilities, of categorization systems and higher-level representations of affordances or social constructs, of the emergence of values, empathy, or theories of mind. === Mechanisms and constraints === The sensorimotor and social spaces in which humans and robot live are so large and complex that only a small part of potentially learnable skills can actually be explored and learnt within a life-time. Thus, mechanisms and constraints are necessary to guide developmental organisms in their development and control of the growth of complexity. There are several important families of these guiding mechanisms and constraints which are studied in developmental robotics, all inspired by human development: Motivational systems, generating internal reward signals that drive exploration and learning, which can be of two main types: extrinsic motivations push robots/organisms to maintain basic specific internal properties such as food and water level, physical integrity, or light (e.g. in phototropic systems); intrinsic motivations push robot to search for novelty, challenge, compression or learning progress per se, thus generating what is sometimes called curiosity-driven learning and exploration, or alternatively active learning and exploration; Social guidance: as humans learn a lot by interacting with their peers, developmental robotics investigates mechanisms that can allow robots to participate to human-like social interaction. By perceiving and interpreting social cues, this may allow robots both to learn from humans (through diverse means such as imitation, emulation, stimulus enhancement, demonstration, etc. ...) and to trigger natural human pedagogy. Thus, social acceptance of developmental robots is also investigated; Statistical inference biases and cumulative knowledge/skill reuse: biases characterizing both representations/encodings and inference mechanisms can typically allow considerable improvement of the efficiency of learning and are thus studied. Related to this, mechanisms allowing to infer new knowledge and acquire new skills by reusing previously learnt structures is also an essential field of study; The properties of embodiment, including geometry, materials, or innate motor primitives/synergies often encoded as dynamical systems, can considerably simplify the acquisition of sensorimotor or social skills, and is sometimes referred as morphological computation. The interaction of these constraints with other constraints is an important axis of investigation; Maturational constraints: In human infants, both the body and the neural system grow progressively, rather than being full-fledged already at birth. This implies, for example, that new degrees of freedom, as well as increases of the volume and resolution of available sensorimotor signals, may appear as learning and development unfold. Transposing these mechanisms in developmental robots, and understanding how it may hinder or on the contrary ease the acquisition of novel complex skills is a central questi

  Read more →
• 

  Pixel-art scaling algorithms

  Pixel art scaling algorithms are graphical filters that attempt to enhance the appearance of hand-drawn 2D pixel art graphics. These algorithms are a form of automatic image enhancement. Pixel art scaling algorithms employ methods significantly different than the common methods of image rescaling, which have the goal of preserving the appearance of images. As pixel art graphics are commonly used at very low resolutions, they employ careful coloring of individual pixels. This results in graphics that rely on a high amount of stylized visual cues to define complex shapes. Several specialized algorithms have been developed to handle re-scaling of such graphics. These specialized algorithms can improve the appearance of pixel-art graphics, but in doing so they introduce changes. Such changes may be undesirable, especially if the goal is to faithfully reproduce the original appearance. Since a typical application of this technology is improving the appearance of fourth-generation and earlier video games on arcade and console emulators, many pixel art scaling algorithms are designed to run in real-time for sufficiently small input images at 60-frames per second. This places constraints on the type of programming techniques that can be used for this sort of real-time processing. Many work only on specific scale factors. 2× is the most common scale factor, while 3×, 4×, 5×, and 6× exist but are less used. == Algorithms == === SAA5050 'Diagonal Smoothing' === The Mullard SAA5050 Teletext character generator chip (1980) used a primitive pixel scaling algorithm to generate higher-resolution characters on the screen from a lower-resolution representation from its internal ROM. Internally, each character shape was defined on a 5 × 9 pixel grid, which was then interpolated by smoothing diagonals to give a 10 × 18 pixel character, with a characteristically angular shape, surrounded to the top and the left by two pixels of blank space. The algorithm only works on monochrome source data, and assumes the source pixels will be logically true or false depending on whether they are 'on' or 'off'. Pixels 'outside the grid pattern' are assumed to be off. The algorithm works as follows: A B C --\ 1 2 D E F --/ 3 4 1 = B | (A & E & !B & !D) 2 = B | (C & E & !B & !F) 3 = E | (!A & !E & B & D) 4 = E | (!C & !E & B & F) Note that this algorithm, like the Eagle algorithm below, has a flaw: If a pattern of 4 pixels in a hollow diamond shape appears, the hollow will be obliterated by the expansion. The SAA5050's internal character ROM carefully avoids ever using this pattern. The degenerate case: becomes: === EPX/Scale2×/AdvMAME2× === Eric's Pixel Expansion (EPX) is an algorithm developed by Eric Johnston at LucasArts around 1992, when porting the SCUMM engine games from the IBM PC (which ran at 320 × 200 × 256 colors) to the early color Macintosh computers, which ran at more or less double that resolution. The algorithm works as follows, expanding P into 4 new pixels based on P's surroundings: 1=P; 2=P; 3=P; 4=P; IF C==A => 1=A IF A==B => 2=B IF D==C => 3=C IF B==D => 4=D IF of A, B, C, D, three or more are identical: 1=2=3=4=P Later implementations of this same algorithm (as AdvMAME2× and Scale2×, developed around 2001) are slightly more efficient but functionally identical: 1=P; 2=P; 3=P; 4=P; IF C==A AND C!=D AND A!=B => 1=A IF A==B AND A!=C AND B!=D => 2=B IF D==C AND D!=B AND C!=A => 3=C IF B==D AND B!=A AND D!=C => 4=D AdvMAME2× is available in DOSBox via the scaler=advmame2x dosbox.conf option. The AdvMAME4×/Scale4× algorithm is just EPX applied twice to get 4× resolution. ==== Scale3×/AdvMAME3× and ScaleFX ==== The AdvMAME3×/Scale3× algorithm (available in DOSBox via the scaler=advmame3x dosbox.conf option) can be thought of as a generalization of EPX to the 3× case. The corner pixels are calculated identically to EPX. 1=E; 2=E; 3=E; 4=E; 5=E; 6=E; 7=E; 8=E; 9=E; IF D==B AND D!=H AND B!=F => 1=D IF (D==B AND D!=H AND B!=F AND E!=C) OR (B==F AND B!=D AND F!=H AND E!=A) => 2=B IF B==F AND B!=D AND F!=H => 3=F IF (H==D AND H!=F AND D!=B AND E!=A) OR (D==B AND D!=H AND B!=F AND E!=G) => 4=D 5=E IF (B==F AND B!=D AND F!=H AND E!=I) OR (F==H AND F!=B AND H!=D AND E!=C) => 6=F IF H==D AND H!=F AND D!=B => 7=D IF (F==H AND F!=B AND H!=D AND E!=G) OR (H==D AND H!=F AND D!=B AND E!=I) => 8=H IF F==H AND F!=B AND H!=D => 9=F There is also a variant improved over Scale3× called ScaleFX, developed by Sp00kyFox, and a version combined with Reverse-AA called ScaleFX-Hybrid. === Eagle === Eagle works as follows: for every in pixel, we will generate 4 out pixels. First, set all 4 to the color of the pixel we are currently scaling (as nearest-neighbor). Next look at the three pixels above, to the left, and diagonally above left: if all three are the same color as each other, set the top left pixel of our output square to that color in preference to the nearest-neighbor color. Work similarly for all four pixels, and then move to the next one. Assume an input matrix of 3 × 3 pixels where the centermost pixel is the pixel to be scaled, and an output matrix of 2 × 2 pixels (i.e., the scaled pixel) first: |Then . . . --\ CC |S T U --\ 1 2 . C . --/ CC |V C W --/ 3 4 . . . |X Y Z | IF V==S==T => 1=S | IF T==U==W => 2=U | IF V==X==Y => 3=X | IF W==Z==Y => 4=Z Thus if we have a single black pixel on a white background it will vanish. This is a bug in the Eagle algorithm but is solved by other algorithms such as EPX, 2xSaI, and HQ2x. === 2×SaI === 2×SaI, short for 2× Scale and Interpolation engine, was inspired by Eagle. It was designed by Derek Liauw Kie Fa, also known as Kreed, primarily for use in console and computer emulators, and it has remained fairly popular in this niche. Many of the most popular emulators, including ZSNES and VisualBoyAdvance, offer this scaling algorithm as a feature. Several slightly different versions of the scaling algorithm are available, and these are often referred to as Super 2×SaI and Super Eagle. The 2xSaI family works on a 4 × 4 matrix of pixels where the pixel marked A below is scaled: I E F J G A B K --\ W X H C D L --/ Y Z M N O P For 16-bit pixels, they use pixel masks which change based on whether the 16-bit pixel format is 565 or 555. The constants colorMask, lowPixelMask, qColorMask, qLowPixelMask, redBlueMask, and greenMask are 16-bit masks. The lower 8 bits are identical in either pixel format. Two interpolation functions are described: INTERPOLATE(uint32 A, UINT32 B). -- linear midpoint of A and B if (A == B) return A; return ( ((A & colorMask) >> 1) + ((B & colorMask) >> 1) + (A & B & lowPixelMask) ); Q_INTERPOLATE(uint32 A, uint32 B, uint32 C, uint32 D) -- bilinear interpolation; A, B, C, and D's average x = ((A & qColorMask) >> 2) + ((B & qColorMask) >> 2) + ((C & qColorMask) >> 2) + ((D & qColorMask) >> 2); y = (A & qLowPixelMask) + (B & qLowPixelMask) + (C & qLowPixelMask) + (D & qLowPixelMask); y = (y >> 2) & qLowPixelMask; return x + y; The algorithm checks A, B, C, and D for a diagonal match such that A==D and B!=C, or the other way around, or if they are both diagonals or if there is no diagonal match. Within these, it checks for three or four identical pixels. Based on these conditions, the algorithm decides whether to use one of A, B, C, or D, or an interpolation among only these four, for each output pixel. The 2xSaI arbitrary scaler can enlarge any image to any resolution and uses bilinear filtering to interpolate pixels. Since Kreed released the source code under the GNU General Public License, it is freely available to anyone wishing to utilize it in a project released under that license. Developers wishing to use it in a non-GPL project would be required to rewrite the algorithm without using any of Kreed's existing code. It is available in DOSBox via scaler=2xsai option. === hqnx family === Maxim Stepin's hq2x, hq3x, and hq4x are for scale factors of 2:1, 3:1, and 4:1 respectively. Each work by comparing the color value of each pixel to those of its eight immediate neighbors, marking the neighbors as close or distant, and using a pre-generated lookup table to find the proper proportion of input pixels' values for each of the 4, 9 or 16 corresponding output pixels. The hq3x family will perfectly smooth any diagonal line whose slope is ±0.5, ±1, or ±2 and which is not anti-aliased in the input; one with any other slope will alternate between two slopes in the output. It will also smooth very tight curves. Unlike 2xSaI, it anti-aliases the output. hqnx was initially created for the Super NES emulator ZSNES. The author of bsnes has released a space-efficient implementation of hq2x to the public domain. A port to shaders, which has comparable quality to the early versions of xBR, is available. Before the port, a shader called "scalehq" has often been confused for hqx. === xBR family === There are 6 filters in this family: xBR , xBRZ, xBR-Hybrid, Super xBR, xBR+3D and Super xBR+3D. xBR ("scale by rules"), cre

  Read more →
• 

  Clue (mobile app)

  Clue is a menstrual health app developed by the Berlin-based technology company BioWink GmbH. The app has over 15 million users from 180 countries. The startup has raised over $17 million from backers that include Union Square Ventures and Mosaic Ventures. == History == Clue was co-founded by Ida Tin, Hans Raffauf, Mike LaVigne and Moritz von Buttlar in 2012. BioWink GmbH launched the app in 2013. Ida Tin's stated goal was to take female reproductive health “out of taboo land” and to start “a reproductive health revolution.” Tin previously led motorbike tours around the world and wrote a book about her experience. By July 2017, the Clue app had more than 8 million active users on both Android and iOS. Users were representative of more than 180 countries. In 2015, BioWink GmbH closed a $7 million Series A funding round led by Union Square Ventures and Mosaic Ventures, bringing the company's total funding to $10 million. The company was listed as one of Europe's Hottest Startups in 2015 by Wired UK, with Clue being named one of the best apps in 2015 by both Apple and Google. In March 2018, the company launched an editorial site to serve as a resource for accessible and scientific menstrual health information. == Mobile app == The Clue mobile application calculates and predicts a user's period, fertile window, and premenstrual syndrome. It also informs users the most or least likely time for becoming pregnant and allows them to track more than 30 health categories, including sex, sleep, pain, exercise, hair, skin, digestion, emotions and energy. The app can also explain how pill dosages impact fertility and includes an alarm system to allow for reminders for taking pills. In 2015, the company closed a Series A funding round and announced plans to use the proceeds to expand features of the mobile app and hire more staff. Clue also partnered with universities such as Stanford University, Columbia University, University of Washington, and University of Oxford to advance female health research. Clue integrated with Apple Inc.'s HealthKit for iOS 9 in September 2015, allowing data such as body temperature, cervical mucus quality, menstruation, ovulation test results, sexual activity, and spotting directly to the app. In 2016, Clue was available in 15 languages on both iOS and Android. That same year, Clue introduced a cycle-sharing feature and in 2017 a pill-tracking option. In February 2018, Clue made its app available on the Fitbit Ionic smartwatch. In 2026, Clue partnered with UK-based digital healthcare platform Evaro, an NHS-licensed provider, to offer embedded prescription services within the app.

  Read more →
• 

  Automated restaurant

  An automated restaurant or robotic restaurant is a restaurant that uses robots to do tasks such as delivering food and drink to the tables or cooking the food. Restaurant automation means the use of a restaurant management system to automate some or occasionally all of the major operations of a restaurant establishment. More recently, restaurants are opening that have completely or partially automated their services. These may include: taking orders, preparing food, serving, and billing. A few fully automated restaurants operate without any human intervention whatsoever. Robots are designed to help and sometimes replace human labour (such as waiters and chefs). The automation of restaurants may also allow for the option for greater customization of an order. == History == === Vending machines === In the late 19th and early 20th century a number of restaurants served food solely through vending machines. These restaurants were called automats or, in Japan, shokkenki. Customers ordered their food directly through the machines. === Sushi conveyors === Yoshiaki Shiraishi is a Japanese innovator who is known for the creation of conveyor belt sushi. He had the idea following difficulty staffing his small sushi restaurant and managing the restaurant on his own. He was inspired seeing beer bottles on a conveyor belt in an Asahi brewery. Yoshiaki's restaurants are an early example of restaurant automation; they used a conveyor belt to distribute dishes around the restaurant, eliminating the need for waiters. This example of automation dates back to the Japanese economic miracle; the first of Yoshiaki's conveyor belt sushi restaurants was opened under the name Mawaru Genroku Sushi in 1958, in Osaka. === Partial automation === As of 2011, across Europe, McDonald's had already begun implementing 7,000 touch screen kiosks that could handle cashiering duties. From 2015 to 2020, Zume had an automated pizza parlor. Later companies would try to produce smaller, less ambitious devices, with one robotics company producing a machine that could automate the slowest and most repetitive parts of assembling a pizza, such as spreading pizza sauce or placing slices of pepperoni, while leaving other customizations to employees. In 2020, a restaurant in the Netherlands began trialling the use of a robot to serve guests. In September 2021, Karakuri's 'Semblr' food service robot served personalised lunches for the 4,000 employees of grocery technology solutions provider ocado Group's head offices in Hatfield, UK. 2,700 different combinations of dishes were on offer. Customers could specify in grams what hot and cold items, proteins, sauces and fresh toppings they wanted. In 2021, Columbia University School of Engineering and Applied Science engineers developed a method of cooking 3D printed chicken with software-controlled robotic lasers. The “Digital Food” team exposed raw 3D printed chicken structures to both blue and infrared light. They then assessed the cooking depth, colour development, moisture retention and flavour differences of the laser-cooked 3D printed samples in comparison to stove-cooked meat. In June 2022 a California nonprofit chain of residential communities, Front Porch, experimented with robots in dining rooms at two locations to supplement wait staff by carrying plated food and drink to tables, and removing dishes. 65% of residents found the robots helpful, with 51% saying they let the staff spend more quality time with diners. 51% of staff were "excited" and 58% said they enabled more quality time with diners. The chain has 19 senior living communities (and 35 affordable housing communities), so it has potential to expand robots to more dining rooms. It is shifting to memory care, which may affect plans. == Rationales == === Advantages === Efficiency: Automated restaurants can significantly enhance operational efficiency by minimizing human error and reducing service time. With automated ordering, payment, and food preparation systems, customers can enjoy faster service and reduced waiting times. Cost savings: By reducing the need for human staff, automated restaurants can potentially lower labor costs. This can be particularly beneficial in areas with high labor expenses, as it allows for better resource allocation and cost management. Consistency: Automation ensures consistency in food quality and presentation. With precise portion control and standardized cooking methods, customers can expect the same quality and taste in their meals every time they visit. Enhanced customer experience: Self-service kiosks and automated systems provide customers with control and convenience. They can customize their orders, browse through menu options, and pay seamlessly, creating a more interactive and satisfying dining experience. === Disadvantages === Lack of personal touch: Automated restaurants may lack the personal interaction and warmth that traditional restaurants provide. Some customers prefer the human touch, personalized recommendations, and the social aspect of dining out. Technical issues: Reliance on technology means that technical glitches and malfunctions can occur, resulting in service disruptions or delays. Maintenance and technical support become critical in ensuring smooth operations. Limited menu complexity: The automation process may be better suited for standardized menu items rather than complex or customized dishes. The ability to cater to unique dietary preferences or accommodate special requests may be limited. Employment implications: Automated restaurants may result in job losses for traditional restaurant staff, potentially impacting the local workforce. It is important to consider the social and economic implications of adopting such technology. == Locations == Automated restaurants have been opening in many countries. Examples include: Nala Restaurant in Naperville, Illinois Fritz's Railroad Restaurant in Kansas City, Kansas Výtopna, a Railway Restaurant using model trains: franchise of various restaurants and coffeehouses in the Czech Republic Bagger's Restaurant in Nuremberg, Germany FuA-Men Restaurant, a ramen restaurant located in Nagoya, Japan Fōster Nutrition in Buenos Aires, Argentina Dalu Robot Restaurant in Jinan, China Haohai Robot Restaurant in Harbin, China Robot Kitchen Restaurant in Hong Kong Robo-Chef restaurant in Tehran, Iran, started in 2017, is the first robotic and "waiterless" restaurant of the Middle East. MIT graduates opened Spyce Kitchens in downtown Boston, Massachusetts, in 2018 Foodom, under Country Garden Holdings, opened January 12, 2020, in Guangzhou, China Robot Chacha, the first robot restaurant of India, is planning to open in the capital city of New Delhi. Kura Revolving Sushi Bar, with a number of locations in the United States, uses a tablets at tables for ordering, a conveyor belt to deliver food, and robots to deliver drinks and condiments. Chipotle Mexican Grill is beginning to deploy the Hyphen Makeline, which assembles up to 350 bowls and salads automatically per hour, and Chippy, an automatic tortilla chip fryer made by Miso Robotics. Serious Dumplings in Boca Raton, Florida

  Read more →
• 

  CHAOS (chess)

  CHAOS (Chess Heuristics and Other Stuff) is a chess playing program that was developed by programmers working at the RCA Systems Programming division in the late 1960s. It played competitively in computer chess competitions in the 1970s and 1980s. It differed from other programs of that era in its look-ahead philosophy, choosing to use chess knowledge to evaluate fewer positions and continuations as opposed to simple evaluations that relied on deep look-ahead to avoid bad moves. == Introduction == CHAOS was originally developed by Ira Ruben, Fred Swartz, Victor Berman, Joe Winograd and William Toikka while working at RCA in Cinnaminson, NJ. Its name is an acronym for 'Chess Heuristics and Other Stuff.' Program development moved to the Computing Center of the University of Michigan when Swartz changed jobs, and Mike Alexander joined the development group. Swartz, Alexander and Berman were continuously group members from that point onward in CHAOS' evolution, as others of the original authors left and new members contributed episodically. Chess Senior Master Jack O'Keefe contributed to CHAOS' development from about 1980 onwards. CHAOS was written in Fortran, except for low-level board representation manipulations written in assembly language or C. Due to this portability, it ran on RCA, Univac and IBM-compatible mainframes in its lifetime. CHAOS heralds from the mainframe computing era when only machines of that capacity were able to play at a high level. Consequently, development and testing could only take place at off-peak times for production use of the machine. In a competition, CHAOS had to run on a dedicated mainframe with a telephone link to the match venue. In its later years, CHAOS ran on computers on the machine assembly floor of Amdahl Corporation on MTS. == Background == === Chess and artificial intelligence === Mathematicians Claude Shannon and Alan Turing, working separately, were the first to view playing chess as a challenge to machines. Working for AT&T / Bell Labs with its access to telephone switching equipment, Shannon built a relay-based machine that learned how to work its way through a two-dimensional, 5x5 cell maze in 1949. Shannon viewed this as an analogue of the way that organisms learn things about their natural environment. There is a random element to searching it, a memory element to benefit from the search outcome, and a reward element that reinforces learning when the global outcome is favorable to the organism. Soon afterward, Shannon wrote a mathematical analysis of the game of chess, published in 1950. Like with the maze, he broke down game play into the necessary elements for reinforcement learning. Associated with each board configuration a move will be made from, there is a numerical score. To decide what move to make, a player wants to maximize their own position's score after the move and to minimize their opponent's score (a minimax view). Since there are about 32 possible moves at each of the early stages of the game, and about 40 moves and responses in each game, then there are about 32 80 {\displaystyle 32^{80}} or about 10 120 {\displaystyle 10^{120}} possible games - an impossibly large set to evaluate completely. Therefore, there must be a way to limit the number of moves to look ahead for to find the best one. Reducing the game to these few key elements provided a way to think about human intelligence in general. Shannon became part of a wider group using computing machines to mimic aspects of human intelligence that grew into the general idea of artificial intelligence. (Other members of this group were John McCarthy, Herbert Simon, Allen Newell, Alan Kotok, Alex Bernstein and Richard Greenblatt.) The paradigm that evolved was that there was a quantification of the position on the board into a score, an evaluation method to find favorable outcomes (minimax, later alpha-beta pruning), and a strategy to manage the combinatorial explosion of the look-ahead possibilities. By the early 1960s, there were computer programs that played chess at a rudimentary level. They used very simple evaluation functions for each position and tried to search as far forward as was practical given the time constraints and available compute power. Naturally, programmers optimized their code to use the available computing resources. This led to a major philosophical divide among chess programs: those that tried to evaluate as many positions as possible, and those that tried to evaluate the most promising move sequences as deeply as possible. CHAOS was firmly in the camp believing only the most promising moves should be evaluated in depth. Said Swartz, "The 'brute force people' ... look at every (possible move) no matter what garbage it is. Most moves are just terrible, terrible moves, and most computing time is being spent on pure garbage." The program spent more time evaluating each board position in the expectation that it would find the most promising lines of play to explore in depth. In 1983, the then-fastest chess program (Belle) evaluated 110,000 positions per second, and typical programs 1000–50,000 per second, whereas CHAOS evaluated about 50-100 per second. === Machine learning and strategies to manage search === From about 1949 onward, Arthur Samuel began work for IBM on machine learning, culminating in a checkers-playing program in 1952 and publications on the topic. Concurrently, Christopher Strachey created Checkers, a program to play the board game of checkers in 1951, but it had no capacity to learn from its play. Checkers was chosen by both authors because it was simpler than chess yet contained the basic characteristics of an intellectual activity, and, in Samuel's view, was a test-bed in which heuristic procedures and learning processes could be evaluated quickly. Checker playing programs introduced the notion of the game tree and evaluating play to various depths to choose the best move. The complexity of chess, however, promoted it to the status of an analogue for human intelligence, and it attracted computer scientists' attention, who referred to it as research into artificial intelligence (AI). Like checkers, it required a numerical assessment of each arrangement of chess pieces on a board. It also required looking ahead to future moves to decide how to play the present position. Due to the enormous number of possible moves, there had to be a way to confine the look-ahead search to the most promising lines of play. From these factors, the notion of minimax score evaluation developed and, later, alpha-beta tree pruning to abandon looking at positions worse than any that have already been examined. === Chess search strategies === The AI community viewed artificial intelligence as comprising two parts: a way to symbolically quantify the knowledge in hand (a chess board position), and a set of heuristics to limit look-ahead to the consequences of a move. The early chess playing programs attempted to look forward as far as possible, perhaps to 3 moves ahead by each player, and to choose the best outcome. This led to the horizon effect, whereby a key move 4 or more moves ahead would be unexamined and therefore missed. Consequently, the programs were quite weak and heuristics to manage the search became important in their development. CHAOS used a selective search strategy with iterative widening. As chess programs evolved, they incorporated books of opening lines of play from historic sources. Nowadays, book moves are catalogued in machine-readable form, but originally programmers had to type them in. CHAOS had an extensive book for its time of around 10,000 moves that O'Keefe helped to develop. A problem with play from an opening book is the behavior of the program when the play leaves the book: the positional advantage may be so subtle that the evaluation scheme may be unable to understand it, leading to very wide and shallow searches to establish a line of play. The horizon effect again plagues move selection after leaving the book. CHAOS mitigated these problems by only using book lines that it could understand, and by relying on cached analyses of continuations out of the book made while the opponent's clock was running. == Game Play History == CHAOS played in twelve ACM computer chess tournaments and four World Computer Chess Championships (WCCC). Its debut was the ACM computer chess tournament in 1973, taking 2nd place. In 1974, it again won 2nd place in the WCCC, defeating the tournament favorite Chess 4.0 but losing to Kaissa. CHAOS was close to winning the 1980 WCCC, but lost to Belle in a playoff. The 1985 ACM computer chess tournament was CHAOS' last competition. One of CHAOS' notable victories was over Chess 4.0 at the 1974 WCCC tournament. Chess 4.0 was unbeaten by any other program up until then. Playing as white, CHAOS made a knight sacrifice (16 Nd4-e6!!) that traded material for open lines of attack and eventually won the game. CHAOS’ authors thought the move was due to a

  Read more →
• 

  Echo Lake (software)

  Echo Lake (AKA Family Album Creator) was the most notable multimedia software product produced by Delrina, which debuted in June 1995. It was touted internally as a "cross [of] Quark Xpress and Myst". It featured an immersive 3D environment where a user could go to a virtual desktop in a virtual office and assemble video and audio clips along with images, and then print them out as either a virtual book other users of the program could use, or for print. It was a highly innovative product for its time, and ultimately was hampered by the inability of many users able to input their own multimedia content easily into a computer from that period. Creative Wonders bought the rights to the Echo Lake multimedia product, which was re-shaped as an introductory program on multimedia and re-released as Family Album Creator in 1996.

  Read more →
• 

  Corel Designer

  Corel DESIGNER is a vector-based graphics program. It was originally developed by Micrografx, which was bought by Corel in 2001. The last version developed by Micrografx was 9.0 in 2001. This program was later sold as Corel DESIGNER 9. There are still a number of users who continue working with version 9.0, because newer versions of the product are based on a modified CorelDRAW rather than the original product. Corel DESIGNER is effective for the creation of engineering drawings, but also offers many functions for graphic design. Starting with version X5, Corel DESIGNER Technical Suite includes Corel Designer, CorelDRAW and Corel Photo-Paint. X6 was the last release for Windows XP. == Release history and file formats ==

  Read more →
• 

  Clef (app)

  Clef was a San Francisco-based technology company, known for developing a mobile app that created a two-factor authentication for websites. It allowed users to access sites with a single login password management service which stores encrypted passwords in private accounts. It had a standard verification method that requires access to data on the mobile phone to confirm the user's identity. The application required a Wi-Fi or mobile network, and the user could log in by scanning the computer screen with their phone. == History == Clef was founded in 2013 by Mark Hudnall, B. Byrne and Jesse Pollak. It raised $1.6 million in seed funding in November 2014. Clef integrated with many websites and applications, including WordPress. On March 17, 2017, Clef announced they would no longer support the plugin after June 6, 2017; Clef was acquired by Authy, another 2FA service, which later got acquired by Twilio.

  Read more →
• 

  Artificial intelligence of things

  Artificial Intelligence of Things (AIoT) is the combination of artificial intelligence (AI) technologies with the Internet of things (IoT) infrastructure to create systems capable of sensing, learning, and acting on data without continuous human intervention. While IoT focuses on connectivity and sensor data collection, AI enables IoT devices to analyse data in real time and produce actionable outputs, including automated decisions at the edge. == Applications == === Manufacturing and predictive maintenance === Manufacturing accounts for the largest share of AIoT adoption by industry vertical. A common application is predictive maintenance, where sensors measuring vibration, temperature, current draw, and acoustic emissions feed machine learning models trained to detect signatures that precede equipment failure. These systems can flag developing faults weeks or months in advance, and in more advanced deployments can autonomously adjust machine parameters such as motor speed or cooling cycles to delay or prevent failure. === Other industries === In healthcare, AIoT enables remote patient monitoring through wearable devices that collect vital signs and apply AI models to detect anomalies or predict deterioration. In logistics, GPS and telematics sensors combined with AI models support real-time route optimisation, vehicle maintenance prediction, and fuel cost forecasting. Smart building systems use occupancy, temperature, and energy sensors with AI to dynamically adjust HVAC and lighting, reducing energy consumption. == Architecture == AIoT systems typically operate across three layers: a device layer of sensors and actuators that collect data, a connectivity layer that transmits data via protocols such as MQTT or HTTP, and a compute layer where AI models process the data either in the cloud or at the edge. The trend toward edge-based processing, where inference runs on low-cost processors near the data source rather than in a centralised cloud, has accelerated as hardware costs have fallen and applications increasingly require sub-second response times. == Market == Market sizing estimates for AIoT vary significantly depending on scope and definition. Fortune Business Insights valued the AIoT market at USD 35.65 billion in 2023, projecting growth to USD 253.86 billion by 2030 at a compound annual growth rate of 32.4%. Grand View Research estimated the broader market at USD 171.4 billion in 2024 with a CAGR of 31.7% through 2030, reflecting a wider definition that includes AI-integrated hardware components. North America accounted for approximately 40% of global market share in 2024, with the Asia-Pacific region projected as the fastest-growing market.

  Read more →
• 

  Level-set method

  The Level-set method (LSM) is a conceptual framework for using level sets as a tool for numerical analysis of surfaces and shapes. LSM can perform numerical computations involving curves and surfaces on a fixed Cartesian grid without having to parameterize these objects. LSM makes it easier to perform computations on shapes with sharp corners and shapes that change topology (such as by splitting in two or developing holes). These characteristics make LSM effective for modeling objects that vary in time, such as an airbag inflating or a drop of oil floating in water. == Overview == The figure on the right illustrates several ideas about LSM. In the upper left corner is a bounded region with a well-behaved boundary. Below it, the red surface is the graph of a level set function φ {\displaystyle \varphi } determining this shape, and the flat blue region represents the X-Y plane. The boundary of the shape is then the zero-level set of φ {\displaystyle \varphi } , while the shape itself is the set of points in the plane for which φ {\displaystyle \varphi } is positive (interior of the shape) or zero (at the boundary). In the top row, the shape's topology changes as it is split in two. It is challenging to describe this transformation numerically by parameterizing the boundary of the shape and following its evolution. An algorithm can be used to detect the moment the shape splits in two and then construct parameterizations for the two newly obtained curves. On the bottom row, however, the plane at which the level set function is sampled is translated upwards, on which the shape's change in topology is described. It is less challenging to work with a shape through its level-set function rather than with itself directly, in which a method would need to consider all the possible deformations the shape might undergo. Thus, in two dimensions, the level-set method amounts to representing a closed curve Γ {\displaystyle \Gamma } (such as the shape boundary in our example) using an auxiliary function φ {\displaystyle \varphi } , called the level-set function. The curve Γ {\displaystyle \Gamma } is represented as the zero-level set of φ {\displaystyle \varphi } by Γ = { ( x , y ) ∣ φ ( x , y ) = 0 } , {\displaystyle \Gamma =\{(x,y)\mid \varphi (x,y)=0\},} and the level-set method manipulates Γ {\displaystyle \Gamma } implicitly through the function φ {\displaystyle \varphi } . This function φ {\displaystyle \varphi } is assumed to take positive values inside the region delimited by the curve Γ {\displaystyle \Gamma } and negative values outside. == The level-set equation == If the curve Γ {\displaystyle \Gamma } moves in the normal direction with a speed v {\displaystyle v} , then by chain rule and implicit differentiation, it can be determined that the level-set function φ {\displaystyle \varphi } satisfies the level-set equation ∂ φ ∂ t = v | ∇ φ | . {\displaystyle {\frac {\partial \varphi }{\partial t}}=v|\nabla \varphi |.} Here, | ⋅ | {\displaystyle |\cdot |} is the Euclidean norm (denoted customarily by single bars in partial differential equations), and t {\displaystyle t} is time. This is a partial differential equation, in particular a Hamilton–Jacobi equation, and can be solved numerically, for example, by using finite differences on a Cartesian grid. However, the numerical solution of the level set equation may require advanced techniques. Simple finite difference methods fail quickly. Upwinding methods such as the Godunov method are considered better; however, the level set method does not guarantee preservation of the volume and shape of the set level in an advection field that maintains shape and size, for example, a uniform or rotational velocity field. Instead, the shape of the level set may become distorted, and the level set may disappear over a few time steps. Therefore, high-order finite difference schemes, such as high-order essentially non-oscillatory (ENO) schemes, are often required, and even then, the feasibility of long-term simulations is questionable. More advanced methods have been developed to overcome this; for example, combinations of the leveling method with tracking marker particles suggested by the velocity field. == Example == Consider a unit circle in R 2 {\textstyle \mathbb {R} ^{2}} , shrinking in on itself at a constant rate, i.e. each point on the boundary of the circle moves along its inwards pointing normally at some fixed speed. The circle will shrink and eventually collapse down to a point. If an initial distance field is constructed (i.e. a function whose value is the signed Euclidean distance to the boundary, positive interior, negative exterior) on the initial circle, the normalized gradient of this field will be the circle normal. If the field has a constant value subtracted from it in time, the zero level (which was the initial boundary) of the new fields will also be circular and will similarly collapse to a point. This is due to this being effectively the temporal integration of the Eikonal equation with a fixed front velocity. == Applications == In mathematical modeling of combustion, LSM is used to describe the instantaneous flame surface, known as the G equation. Level-set data structures have been developed to facilitate the use of the level-set method in computer applications. Computational fluid dynamics Trajectory planning Optimization Image processing Computational biophysics Discrete complex dynamics (visualization of the parameter plane and the dynamic plane) == History == The level-set method was developed in 1979 by Alain Dervieux, and subsequently popularized by Stanley Osher and James Sethian. It has since become popular in many disciplines, such as image processing, computer graphics, computational geometry, optimization, computational fluid dynamics, and computational biology.

  Read more →
• 

  Robotics

  Robotics is the interdisciplinary study and practice of the design, construction, operation, and use of robots. A roboticist is someone who specializes in robotics. Robotics usually combines four aspects of design work: a power source (e.g. a battery), mechanical construction, a control system (electrical circuits), and software (run by remote control or artificial intelligence). The goal of most robotics is to design machines that can assist humans in various fields, such as agriculture, construction, domestic work, food processing, inventory management, manufacturing, medicine, military, mining, space exploration, and transportation. Robots impact humans by displacing workers. Some expect this to occur at an increasing rate, leading to proposed solutions such as basic income. Robotics is itself a lucrative business that creates careers, especially for postgraduates. Roboticists often aim to create machines that seem to interface naturally with humans. The field is under active research and development, with areas of interest including robot kinematics and quantum robotics. == Design == Robotics usually combines four aspects of design work to create a robot: Power source: Potential energy sources include wired electricity, a battery, and/or petrol. Mechanical construction: A physical form or combination of forms is designed to functionally achieve tasks within a given range of environments. This can include locomotive elements such as wheels and caterpillar tracks, as well as hydraulic limbs and manipulators (e.g. hands). Control system: Electrical circuits (utilizing components such as diodes and transistors) are used to run software, govern motor movement, and read sensors. Software: A program is how a robot decides when or how to do something. Robotic programs can be run by remote control, artificial intelligence (AI), or a hybrid of the two. AI programming is an important part of robotic navigation and human–robot interaction. === Power source === Many different types of batteries can be used as a power source. Most are lead–acid batteries, which are safe and have relatively long shelf lives but are rather heavy compared to silver–cadmium batteries, which are much smaller in volume and much more expensive. Designing a battery-powered robot needs to take into account factors such as safety, cycle lifetime, and weight. Generators, often some type of internal combustion engine, can also be used, but are often mechanically complex and inefficient. Additionally, a tether could connect the robot to a power supply, saving weight and space, but requiring a cumbersome cable. Potential power sources include: Flywheel energy storage Hydraulics Nuclear Organic garbage (through anaerobic digestion) Pneumatics (compressed gases) Solar power === Mechanical construction === Actuators are the "muscles" of a robot, the parts which convert stored energy into movement. The most popular actuators are electric motors that rotate a wheel or gear and linear actuators that control factory robots. Most robots use electric motors—often brushed and brushless DC motors in portable robots or AC motors in industrial robots and computer numerical control machines—especially in systems with lighter loads and where the predominant form of motion is rotational. Meanwhile, linear actuators move in and out and often have quicker direction changes, particularly when large forces are needed, such as with industrial robotics. They are typically powered by oil or compressed air, but can also be powered by electricity, usually via a motor and a leadscrew. The mechanical rack and pinion is common. Recent alternatives to DC motors are piezoelectric motors, including ultrasonic motors, in which tiny piezoceramic elements vibrate many thousands of times per second, causing linear or rotary motion. One type uses the vibration of the piezo elements to step the motor in a circle or a straight line; another type uses the piezo elements to vibrate a nut or drive a screw. The advantages of these motors are nanometer resolution, speed, and force for their size. Series elastic actuation (SEA) relies on introducing intentional elasticity between the motor actuator and the load for robust force control. Due to the resultant lower reflected inertia, series elastic actuation improves safety during robot interactions or collisions. Further, it provides energy efficiency and shock absorption (mechanical filtering) while reducing excessive wear on the transmission and other components. This approach has successfully been employed in various robots, particularly advanced manufacturing robots and walking humanoid robots. The controller design of a series elastic actuator is most often performed within the passivity framework as it ensures the safety of interaction with unstructured environments. However, this framework suffers from stringent limitations imposed on the controller, which may impact performance. Pneumatic artificial muscles, also known as air muscles, are special tubes that expand (typically up to 42%) when air is forced inside them; they are used in some robot applications. Muscle wire, also known as shape memory alloy, is a material that contracts (under 5%) when electricity is applied; they have been used for some small robots. Electroactive polymers are a plastic material that can contract substantially (up to 380% activation strain) from electricity and have been used in the facial muscles and arms of humanoid robots, as well as to enable new robots to float, fly, swim or walk. Additionally, elastic carbon nanotubes are a promising experimental artificial muscle technology. The absence of defects in carbon nanotubes enables these filaments to deform elastically by several percent, with energy storage levels of perhaps 10 J/cm3 for metal nanotubes. Human biceps could be replaced with wire of this material measuring 8 millimetres (3⁄8 in) in diameter, feasibly allowing future robots to outperform humans. ==== Locomotion ==== Robots with only one or two wheel(s) can have advantages such as greater efficiency, reduced parts, and navigation through confined areas. A one-wheeled robot balances on a round ball; Carnegie Mellon University's Ballbot is the approximate height and width of a person. Several attempts have also been made to build spherical robots (also known as orb bots or ball bots), which move by spinning a weight inside the ball or rotating outer shells. Two-wheeled balancing robots generally use a gyroscope to detect how much a robot is falling and drive the wheels proportionally up to hundreds of times per second to counterbalance the fall, based on inverted pendulum dynamics. NASA's Robonaut has been mounted to a Segway for a similar effect. Most mobile robots have four wheels or continuous tracks. Six wheels can give better traction in outdoor terrain, while tracks provide even more grip. Tracked wheels are common for outdoor off-road robots, but are difficult to use indoors. A small number of skating robots have been developed, one of which is a multimodal walking and skating device with four legs and unpowered wheels. Several robots have been made that can walk on two legs, but not yet as reliably as a human. Many other robots have been built that walk on more than two legs, being significantly easier. Walking robots could be used for uneven terrains, providing a high degree of mobility and efficiency, but two-legged robots can currently only handle flat floors or perhaps stairs. Some approaches have included: The zero moment point (ZMP) is the algorithm used by robots such as Honda's ASIMO. The robot's onboard computer tries to keep the total inertial forces (the combination of Earth's gravity and the acceleration and deceleration of walking) exactly opposed by the floor reaction force (the force of the floor pushing back on the robot's foot). In this way, the two forces cancel out, leaving no moment (force causing the robot to rotate and fall over). Human observers note that this is not exactly how a human walks, with some describing ASIMO's walk as looking like it needs use the bathroom. ASIMO's walking algorithm utilizes some dynamic balancing, but requires a flat surface. Several robots, built in the 1980s by Marc Raibert at the MIT Leg Laboratory, successfully demonstrated very dynamic walking. Initially, a robot with only one leg, and a very small foot could stay upright simply by hopping. The movement is the same as that of a person on a pogo stick. As the robot falls to one side, it would jump slightly in that direction to catch itself. Soon, the algorithm was generalized to two and four legs. A bipedal robot was demonstrated running and even performing somersaults. A quadruped was also demonstrated which could trot, run, pace, and bound. A more advanced approach is a dynamic balancing algorithm, which constantly monitors the robot's motion and places the feet to maintain stability. This technique has been demonstrated by Anybots' Dexter robot (

  Read more →