Visual servoing, also known as vision-based robot control and abbreviated VS, is a technique which uses feedback information extracted from a vision sensor (visual feedback) to control the motion of a robot. One of the earliest papers that talks about visual servoing was from the SRI International Labs in 1979. == Visual servoing taxonomy == There are two fundamental configurations of the robot end-effector (hand) and the camera: Eye-in-hand, or end-point open-loop control, where the camera is attached to the moving hand and observing the relative position of the target. Eye-to-hand, or end-point closed-loop control, where the camera is fixed in the world and observing the target and the motion of the hand. Visual Servoing control techniques are broadly classified into the following types: Image-based (IBVS) Position/pose-based (PBVS) Hybrid approach IBVS was proposed by Weiss and Sanderson. The control law is based on the error between current and desired features on the image plane, and does not involve any estimate of the pose of the target. The features may be the coordinates of visual features, lines or moments of regions. IBVS has difficulties with motions very large rotations, which has come to be called camera retreat. PBVS is a model-based technique (with a single camera). This is because the pose of the object of interest is estimated with respect to the camera and then a command is issued to the robot controller, which in turn controls the robot. In this case the image features are extracted as well, but are additionally used to estimate 3D information (pose of the object in Cartesian space), hence it is servoing in 3D. Hybrid approaches use some combination of the 2D and 3D servoing. There have been a few different approaches to hybrid servoing 2-1/2-D Servoing Motion partition-based Partitioned DOF Based == Survey == The following description of the prior work is divided into 3 parts Survey of existing visual servoing methods. Various features used and their impacts on visual servoing. Error and stability analysis of visual servoing schemes. === Survey of existing visual servoing methods === Visual servo systems, also called servoing, have been around since the early 1980s , although the term visual servo itself was only coined in 1987. Visual Servoing is, in essence, a method for robot control where the sensor used is a camera (visual sensor). Servoing consists primarily of two techniques, one involves using information from the image to directly control the degrees of freedom (DOF) of the robot, thus referred to as Image Based Visual Servoing (IBVS). While the other involves the geometric interpretation of the information extracted from the camera, such as estimating the pose of the target and parameters of the camera (assuming some basic model of the target is known). Other servoing classifications exist based on the variations in each component of a servoing system , e.g. the location of the camera, the two kinds are eye-in-hand and hand–eye configurations. Based on the control loop, the two kinds are end-point-open-loop and end-point-closed-loop. Based on whether the control is applied to the joints (or DOF) directly or as a position command to a robot controller the two types are direct servoing and dynamic look-and-move. Being one of the earliest works the authors proposed a hierarchical visual servo scheme applied to image-based servoing. The technique relies on the assumption that a good set of features can be extracted from the object of interest (e.g. edges, corners and centroids) and used as a partial model along with global models of the scene and robot. The control strategy is applied to a simulation of a two and three DOF robot arm. Feddema et al. introduced the idea of generating task trajectory with respect to the feature velocity. This is to ensure that the sensors are not rendered ineffective (stopping the feedback) for any the robot motions. The authors assume that the objects are known a priori (e.g. CAD model) and all the features can be extracted from the object. The work by Espiau et al. discusses some of the basic questions in visual servoing. The discussions concentrate on modeling of the interaction matrix, camera, visual features (points, lines, etc..). In an adaptive servoing system was proposed with a look-and-move servoing architecture. The method used optical flow along with SSD to provide a confidence metric and a stochastic controller with Kalman filtering for the control scheme. The system assumes (in the examples) that the plane of the camera and the plane of the features are parallel., discusses an approach of velocity control using the Jacobian relationship s˙ = Jv˙ . In addition the author uses Kalman filtering, assuming that the extracted position of the target have inherent errors (sensor errors). A model of the target velocity is developed and used as a feed-forward input in the control loop. Also, mentions the importance of looking into kinematic discrepancy, dynamic effects, repeatability, settling time oscillations and lag in response. Corke poses a set of very critical questions on visual servoing and tries to elaborate on their implications. The paper primarily focuses the dynamics of visual servoing. The author tries to address problems like lag and stability, while also talking about feed-forward paths in the control loop. The paper also, tries to seek justification for trajectory generation, methodology of axis control and development of performance metrics. Chaumette in provides good insight into the two major problems with IBVS. One, servoing to a local minima and second, reaching a Jacobian singularity. The author show that image points alone do not make good features due to the occurrence of singularities. The paper continues, by discussing the possible additional checks to prevent singularities namely, condition numbers of J_s and Jˆ+_s, to check the null space of ˆ J_s and J^T_s . One main point that the author highlights is the relation between local minima and unrealizable image feature motions. Over the years many hybrid techniques have been developed. These involve computing partial/complete pose from Epipolar Geometry using multiple views or multiple cameras. The values are obtained by direct estimation or through a learning or a statistical scheme. While others have used a switching approach that changes between image-based and position-based on a Lyapnov function. The early hybrid techniques that used a combination of image-based and pose-based (2D and 3D information) approaches for servoing required either a full or partial model of the object in order to extract the pose information and used a variety of techniques to extract the motion information from the image. used an affine motion model from the image motion in addition to a rough polyhedral CAD model to extract the object pose with respect to the camera to be able to servo onto the object (on the lines of PBVS). 2-1/2-D visual servoing developed by Malis et al. is a well known technique that breaks down the information required for servoing into an organized fashion which decouples rotations and translations. The papers assume that the desired pose is known a priori. The rotational information is obtained from partial pose estimation, a homography, (essentially 3D information) giving an axis of rotation and the angle (by computing the eigenvalues and eigenvectors of the homography). The translational information is obtained from the image directly by tracking a set of feature points. The only conditions being that the feature points being tracked never leave the field of view and that a depth estimate be predetermined by some off-line technique. 2-1/2-D servoing has been shown to be more stable than the techniques that preceded it. Another interesting observation with this formulation is that the authors claim that the visual Jacobian will have no singularities during the motions. The hybrid technique developed by Corke and Hutchinson, popularly called portioned approach partitions the visual (or image) Jacobian into motions (both rotations and translations) relating X and Y axes and motions related to the Z axis. outlines the technique, to break out columns of the visual Jacobian that correspond to the Z axis translation and rotation (namely, the third and sixth columns). The partitioned approach is shown to handle the Chaumette Conundrum discussed in. This technique requires a good depth estimate in order to function properly. outlines a hybrid approach where the servoing task is split into two, namely main and secondary. The main task is keep the features of interest within the field of view. While the secondary task is to mark a fixation point and use it as a reference to bring the camera to the desired pose. The technique does need a depth estimate from an off-line procedure. The paper discusses two examples for which depth estimates are obtained from robot odometry and by assuming that all
Umoove
Umoove is a high tech startup company that has developed and patented a software-only face and eye tracking technology. The idea was first conceived as an attempt to aid people with disabilities but has since evolved. The only compatibility qualification for tablet computers and smartphones to run Umoove software is a front-facing camera. Umoove headquarters are in Israel on Jerusalem’s Har Hotzvim. Umoove has 15 employees and received two million dollars in financing in 2012. The company's original founders invested around $800,000 to start the business in 2010. In 2013 Umoove was named one of the top three most promising Israeli start ups by Newsgeeks magazine. The company also participated in the 2013 LeWeb conference in Paris, France, where innovative technology startups are showcased. == Technology == The technology uses information extracted from previous frames, such as the angle of the user's head to predict where to look for facial targets in the next frame. This anticipation minimizes the amount of computation needed to scan each image. Umoove accounts for variances in environment, lighting conditions and user hand shake/movement. The technology is designed to provide a consistent experience, whether you're in a brightly lit area or a darkened basement, and to work fluidly between them by adapting its processing when it detects color and brightness shifts. It uses an active stabilization technique to filter out natural body movements from an unstable camera in order to minimize false-positive motion detection. Running the Umoove software on a Samsung Galaxy S3 is said to take up only 2% CPU. Umoove works exclusively with software and there is no hardware add-on necessary. It can be run on any smartphone or tablet computer that has a front-facing camera. Umoove claims that even a low-quality camera on an old device will run their software flawlessly. == Umoove Experience == In January 2014 Umoove released its first game onto the app store. The Umoove Experience game lets users control where they are 'flying' in the game through simple gestures and motions with their head. The avatar will basically go toward wherever the user looks. The game was created to showcase the technology for game developers but that did not stop some from criticizing its simplicity. Umoove also announced that they raised another one million dollars and that they are opening offices in Silicon Valley, California. In February 2014, Umoove announced that their face-tracking software development kit is available for Android developers as well as iOS. == Reviews == The Umoove Experience garnered mostly positive reviews from bloggers and mainstream media with some predicting that it could be the future of mobile gaming. Mashable wrote that Umoove's technology could be the emergence of gesture recognition technology in the mobile space, similar to Kinect with console gaming and what Leap Motion has done with desktop computers. Some, however, remain skeptical. CNET, for example, did not give the game a positive review and called the eye tracking technology 'freaky but cool'. They also noted that pioneering technologies have been known to fall short of expectations, citing Apple Inc’s Siri as an example. The technology blog GigaOM said that the Umoove Experience is ’awesome’ and technology evangelist Robert Scoble has called Umoove "brilliant". == uHealth == In January 2015, Umoove released uHealth, a mobile application that uses eye tracking game-like exercise to challenge the user's ability to be attentive, continuously focus, follow commands and avoid distractions. The app is designed in the form of two games, one to improve attention and another that hones focus. uHealth is a training tool, not a diagnostic. Umoove has stated that they want to use their technology for diagnosing neurological disorders but this will depend on clinical tests and FDA approval. The company cites the direct relationship between eye movements and brain activity as well as various vision-based therapies have been backed by many scientific studies conducted over the past decades. uHealth is the first time this type of therapy is delivered right to the end user through a simple download. == Collaboration rumors == In March 2013 there were rumors on the internet that Umoove would be the functioning software embedded into the Samsung Galaxy S4, which was due to launch that month. This rumor was perpetrated by, among others, New York Times, Techcrunch and Yahoo. Once Samsung launched without the Umoove technology rumors about a potential collaboration with Apple Inc hit the web. It has been said that due to the fact that Apple Inc is losing market share and stock value to Samsung they will be more aggressive and eye tracking is a logical place to make that move.
VLLM
vLLM is an open-source software framework for inference and serving of large language models and related multimodal models. Originally developed at the University of California, Berkeley's Sky Computing Lab, the project is centered on PagedAttention, a memory-management method for transformer key–value caches, and supports features such as continuous batching, distributed inference, quantization, and OpenAI-compatible APIs. According to a project maintainer, the "v" in vLLM originally referred to "virtual", inspired by virtual memory. == History == vLLM was introduced in 2023 by researchers affiliated with the Sky Computing Lab at UC Berkeley. Its core ideas were described in the 2023 paper Efficient Memory Management for Large Language Model Serving with PagedAttention, which presented the system as a high-throughput and memory-efficient serving engine for large language models. In 2025, the PyTorch Foundation announced that vLLM had become a Foundation-hosted project. PyTorch's project page states that the University of California, Berkeley contributed vLLM to the Linux Foundation in July 2024. In January 2026, TechCrunch reported that the creators of vLLM had launched the startup Inferact to commercialize the project, raising $150 million in seed funding. == Architecture == According to its 2023 paper, vLLM was designed to improve the efficiency of large language model serving by reducing memory waste in the key–value cache used during transformer inference. The paper introduced PagedAttention, an algorithm inspired by virtual memory and paging techniques in operating systems, and described vLLM as using block-level memory management and request scheduling to increase throughput while maintaining similar latency. The project documentation and repository describe support for continuous batching, chunked prefill, speculative decoding, prefix caching, quantization, and multiple forms of distributed inference and serving. PyTorch has described vLLM as a high-throughput, memory-efficient inference and serving engine that supports a range of hardware back ends, including NVIDIA and AMD GPUs, Google TPUs, AWS Trainium, and Intel processors.
Niki.ai
Niki was an artificial intelligence company headquartered in Bangalore, Karnataka. It was founded in May 2015 by IIT Kharagpur graduates Sachin Jaiswal, Keshav Prawasi, Shishir Modi, and Nitin Babel. The Niki android app was launched for a limited beta in June 2015, then released for public during YourStory's TechSparks 2015, and is a Tech30 company. The company raised an undisclosed amount in seed funding from Unilazer Ventures, a Mumbai-based VC firm founded by Ronnie Screwvala, in October 2015. This was followed by another seed funding round by Ratan Tata in May 2016. The company then raised US$2 million in Series A round of funding from SAP.iO, existing investors and some US and German-based investors, among others. Niki.ai shut down in October 2021 as per media reports. Website not working. == Product == The product is an artificial intelligence-powered chatbot which works as an intelligent personal assistant, named Niki. Leveraging natural language processing and machine learning, Niki presents a chat-based natural language user interface to the users where they can interact with Niki in their natural language. Niki understands how users chat in India, deciphers the words, in the context of product/services that they would like to purchase, and comes up with apt recommendations. Initially, it was only available on the Android platform as a mobile app. The company has expanded its operations to the Facebook Messenger and Apple iOS platforms. The company aims to soon be present on more messaging platforms like Slack and WhatsApp. The company currently provides 20+ services to over 2 million consumers, covering a wide spectrum ranging from utility services like mobile recharge, bill payments, travel services like cabs, buses, hotels and entertainment services like movies and events. Services such as flights and healthcare are also planned. == Partnerships == In September 2017, Infosys Finacle joined with Niki.ai to provide chat-based service to banking customers. In August 2017, Niki partnered with LazyPay to enable a 'buy now, pay later' feature for its users.
Condensation algorithm
The condensation algorithm (Conditional Density Propagation) is a computer vision algorithm. The principal application is to detect and track the contour of objects moving in a cluttered environment. Object tracking is one of the more basic and difficult aspects of computer vision and is generally a prerequisite to object recognition. Being able to identify which pixels in an image make up the contour of an object is a non-trivial problem. Condensation is a probabilistic algorithm that attempts to solve this problem. The algorithm itself is described in detail by Isard and Blake in a publication in the International Journal of Computer Vision in 1998. One of the most interesting facets of the algorithm is that it does not compute on every pixel of the image. Rather, pixels to process are chosen at random, and only a subset of the pixels end up being processed. Multiple hypotheses about what is moving are supported naturally by the probabilistic nature of the approach. The evaluation functions come largely from previous work in the area and include many standard statistical approaches. The original part of this work is the application of particle filter estimation techniques. The algorithm's creation was inspired by the inability of Kalman filtering to perform object tracking well in the presence of significant background clutter. The presence of clutter tends to produce probability distributions for the object state which are multi-modal and therefore poorly modeled by the Kalman filter. The condensation algorithm in its most general form requires no assumptions about the probability distributions of the object or measurements. == Algorithm overview == The condensation algorithm seeks to solve the problem of estimating the conformation of an object described by a vector x t {\displaystyle \mathbf {x_{t}} } at time t {\displaystyle t} , given observations z 1 , . . . , z t {\displaystyle \mathbf {z_{1},...,z_{t}} } of the detected features in the images up to and including the current time. The algorithm outputs an estimate to the state conditional probability density p ( x t | z 1 , . . . , z t ) {\displaystyle p(\mathbf {x_{t}} |\mathbf {z_{1},...,z_{t}} )} by applying a nonlinear filter based on factored sampling and can be thought of as a development of a Monte-Carlo method. p ( x t | z 1 , . . . , z t ) {\displaystyle p(\mathbf {x_{t}} |\mathbf {z_{1},...,z_{t}} )} is a representation of the probability of possible conformations for the objects based on previous conformations and measurements. The condensation algorithm is a generative model since it models the joint distribution of the object and the observer. The conditional density of the object at the current time p ( x t | z 1 , . . . , z t ) {\displaystyle p(\mathbf {x_{t}} |\mathbf {z_{1},...,z_{t}} )} is estimated as a weighted, time-indexed sample set { s t ( n ) , n = 1 , . . . , N } {\displaystyle \{s_{t}^{(n)},n=1,...,N\}} with weights π t ( n ) {\displaystyle \pi _{t}^{(n)}} . N is a parameter determining the number of sample sets chosen. A realization of p ( x t | z 1 , . . . , z t ) {\displaystyle p(\mathbf {x_{t}} |\mathbf {z_{1},...,z_{t}} )} is obtained by sampling with replacement from the set s t {\displaystyle s_{t}} with probability equal to the corresponding element of π t {\displaystyle \pi _{t}} . The assumptions that object dynamics form a temporal Markov chain and that observations are independent of each other and the dynamics facilitate the implementation of the condensation algorithm. The first assumption allows the dynamics of the object to be entirely determined by the conditional density p ( x t | x t − 1 ) {\displaystyle p(\mathbf {x_{t}} |\mathbf {x_{t-1}} )} . The model of the system dynamics determined by p ( x t | x t − 1 ) {\displaystyle p(\mathbf {x_{t}} |\mathbf {x_{t-1}} )} must also be selected for the algorithm, and generally includes both deterministic and stochastic dynamics. The algorithm can be summarized by initialization at time t = 0 {\displaystyle t=0} and three steps at each time t: === Initialization === Form the initial sample set and weights by sampling according to the prior distribution. For example, specify as Gaussian and set the weights equal to each other. === Iterative procedure === Sample with replacement N {\displaystyle N} times from the set { s 0 ( n ) , n = 1 , . . . , N } {\displaystyle \{s_{0}^{(n)},n=1,...,N\}} with probability { π 0 ( n ) , n = 1 , . . . , N } {\displaystyle \{\pi _{0}^{(n)},n=1,...,N\}} to generate a realization of p ( x t | z 1 , . . . , z t ) {\displaystyle p(\mathbf {x_{t}} |\mathbf {z_{1},...,z_{t}} )} . Apply the learned dynamics p ( x t | x t − 1 ) {\displaystyle p(\mathbf {x_{t}} |\mathbf {x_{t-1}} )} to each element of this new set, to generate a new set { s t ( n ) } {\displaystyle \{s_{t}^{(n)}\}} . To take into account the current observation z t {\displaystyle \mathbf {z_{t}} } , set π t ( n ) = p ( z t | s ( n ) ) ∑ j = 1 N p ( z t | s ( j ) ) {\displaystyle \pi _{t}^{(n)}={\frac {p(\mathbf {z_{t}} |s^{(n)})}{\sum _{j=1}^{N}p(\mathbf {z_{t}} |s^{(j)})}}} for each element { s t ( n ) } {\displaystyle \{s_{t}^{(n)}\}} . This algorithm outputs the probability distribution p ( x t | z 1 , . . . , z t ) {\displaystyle p(\mathbf {x_{t}} |\mathbf {z_{1},...,z_{t}} )} which can be directly used to calculate the mean position of the tracked object, as well as the other moments of the tracked object. Cumulative weights can instead be used to achieve a more efficient sampling. == Implementation considerations == Since object-tracking can be a real-time objective, consideration of algorithm efficiency becomes important. The condensation algorithm is relatively simple when compared to the computational intensity of the Ricatti equation required for Kalman filtering. The parameter N {\displaystyle N} , which determines the number of samples in the sample set, will clearly hold a trade-off in efficiency versus performance. One way to increase efficiency of the algorithm is by selecting a low degree of freedom model for representing the shape of the object. The model used by Isard 1998 is a linear parameterization of B-splines in which the splines are limited to certain configurations. Suitable configurations were found by analytically determining combinations of contours from multiple views, of the object in different poses, and through principal component analysis (PCA) on the deforming object. Isard and Blake model the object dynamics p ( x t | x t − 1 ) {\displaystyle p(\mathbf {x_{t}} |\mathbf {x_{t-1}} )} as a second order difference equation with deterministic and stochastic components: p ( x t | x t − 1 ) ∝ e − 1 2 | | B − 1 ( ( x t − x ¯ ) − A ( x t − 1 − x ¯ ) ) | | 2 ) {\displaystyle p(\mathbf {x_{t}} |\mathbf {x_{t-1}} )\propto e^{-{\frac {1}{2}}||B^{-1}((\mathbf {x_{t}} -\mathbf {\bar {x}} )-A(\mathbf {x_{t-1}} -\mathbf {\bar {x}} ))||^{2})}} where x ¯ {\displaystyle \mathbf {\bar {x}} } is the mean value of the state, and A {\displaystyle A} , B {\displaystyle B} are matrices representing the deterministic and stochastic components of the dynamical model respectively. A {\displaystyle A} , B {\displaystyle B} , and x ¯ {\displaystyle \mathbf {\bar {x}} } are estimated via Maximum Likelihood Estimation while the object performs typical movements. The observation model p ( z | x ) {\displaystyle p(\mathbf {z} |\mathbf {x} )} cannot be directly estimated from the data, requiring assumptions to be made in order to estimate it. Isard 1998 assumes that the clutter which may make the object not visible is a Poisson random process with spatial density λ {\displaystyle \lambda } and that any true target measurement is unbiased and normally distributed with standard deviation σ {\displaystyle \sigma } . The basic condensation algorithm is used to track a single object in time. It is possible to extend the condensation algorithm using a single probability distribution to describe the likely states of multiple objects to track multiple objects in a scene at the same time. Since clutter can cause the object probability distribution to split into multiple peaks, each peak represents a hypothesis about the object configuration. Smoothing is a statistical technique of conditioning the distribution based on both past and future measurements once the tracking is complete in order to reduce the effects of multiple peaks. Smoothing cannot be directly done in real-time since it requires information of future measurements. == Applications == The algorithm can be used for vision-based robot localization of mobile robots. Instead of tracking the position of an object in the scene, however, the position of the camera platform is tracked. This allows the camera platform to be globally localized given a visual map of the environment. Extensions of the condensation algorithm have also been used to recognize human gestures in image sequences. This application of the condensation algorithm impacts the ran
Microsoft Sway
Microsoft Sway is a presentation program and is part of the Microsoft 365 family of products. Sway was offered for general release by Microsoft in August 2015. It allows users who have a Microsoft account to combine text and media to create a presentable website. Users can pull content locally from the device in use, or from internet sources such as Bing, Facebook, OneDrive, and YouTube. Sway is distinguished from Microsoft FrontPage and Microsoft Expression Web – unrelated web design programs previously developed by Microsoft – in that Sway includes a method for hosting sites. Sway sites are stored on Microsoft's servers and are tied to the user's Microsoft account. They can be viewed and edited from any web browser through Office on the web. There is no offline editing or viewing function, but sites can be accessed using the app for Windows, and formerly iOS. == History == Sway was developed internally by Microsoft. In late 2014, the company announced an invite-only preview version of Sway and announced that Sway would not require an Office 365 subscription. An iOS app was released as a preview on 31 October 2014, but was discontinued on 17 December 2018 due to low usage. As of July 17, 2021, the Sway iOS app's discontinuance in 2018 was the last piece of news posted in the Sway tech blog. The Sway feature blog has not received an update since April 2017. The Microsoft Office Roadmap did not include any items related to Sway ever since. The iOS application is no longer under active development, and is not available for download. Since 2023, Microsoft has been consolidating the domains of its Microsoft 365 apps and services under cloud.microsoft. By 2025, the vast majority of services, including Sway, have already migrated to the cloud.microsoft domain. == Features == Users are able to add content from various sources into their Sway presentations. Some of the integrated services are owned by Microsoft, including OneNote, Bing, and other Sway sites. The program also provides native integration with other services, including YouTube, Facebook, Twitter, Mixcloud, and Infogram.
Semantic interpretation
Semantic interpretation is an important component in dialog systems. It is related to natural language understanding, but mostly it refers to the last stage of understanding. The goal of interpretation is binding the user utterance to concept, or something the system can understand. Typically it is creating a database query based on user utterance.