Visual servoing
Visual servoing, also known as vision-based robot control and abbreviated VS, is a technique which uses feedback information extracted from a vision sensor (visual feedback) to control the motion of a robot. One of the earliest papers that talks about visual servoing was from the SRI International Labs in 1979. == Visual servoing taxonomy == There are two fundamental configurations of the robot end-effector (hand) and the camera: Eye-in-hand, or end-point open-loop control, where the camera is attached to the moving hand and observing the relative position of the target. Eye-to-hand, or end-point closed-loop control, where the camera is fixed in the world and observing the target and the motion of the hand. Visual Servoing control techniques are broadly classified into the following types: Image-based (IBVS) Position/pose-based (PBVS) Hybrid approach IBVS was proposed by Weiss and Sanderson. The control law is based on the error between current and desired features on the image plane, and does not involve any estimate of the pose of the target. The features may be the coordinates of visual features, lines or moments of regions. IBVS has difficulties with motions very large rotations, which has come to be called camera retreat. PBVS is a model-based technique (with a single camera). This is because the pose of the object of interest is estimated with respect to the camera and then a command is issued to the robot controller, which in turn controls the robot. In this case the image features are extracted as well, but are additionally used to estimate 3D information (pose of the object in Cartesian space), hence it is servoing in 3D. Hybrid approaches use some combination of the 2D and 3D servoing. There have been a few different approaches to hybrid servoing 2-1/2-D Servoing Motion partition-based Partitioned DOF Based == Survey == The following description of the prior work is divided into 3 parts Survey of existing visual servoing methods. Various features used and their impacts on visual servoing. Error and stability analysis of visual servoing schemes. === Survey of existing visual servoing methods === Visual servo systems, also called servoing, have been around since the early 1980s , although the term visual servo itself was only coined in 1987. Visual Servoing is, in essence, a method for robot control where the sensor used is a camera (visual sensor). Servoing consists primarily of two techniques, one involves using information from the image to directly control the degrees of freedom (DOF) of the robot, thus referred to as Image Based Visual Servoing (IBVS). While the other involves the geometric interpretation of the information extracted from the camera, such as estimating the pose of the target and parameters of the camera (assuming some basic model of the target is known). Other servoing classifications exist based on the variations in each component of a servoing system , e.g. the location of the camera, the two kinds are eye-in-hand and hand–eye configurations. Based on the control loop, the two kinds are end-point-open-loop and end-point-closed-loop. Based on whether the control is applied to the joints (or DOF) directly or as a position command to a robot controller the two types are direct servoing and dynamic look-and-move. Being one of the earliest works the authors proposed a hierarchical visual servo scheme applied to image-based servoing. The technique relies on the assumption that a good set of features can be extracted from the object of interest (e.g. edges, corners and centroids) and used as a partial model along with global models of the scene and robot. The control strategy is applied to a simulation of a two and three DOF robot arm. Feddema et al. introduced the idea of generating task trajectory with respect to the feature velocity. This is to ensure that the sensors are not rendered ineffective (stopping the feedback) for any the robot motions. The authors assume that the objects are known a priori (e.g. CAD model) and all the features can be extracted from the object. The work by Espiau et al. discusses some of the basic questions in visual servoing. The discussions concentrate on modeling of the interaction matrix, camera, visual features (points, lines, etc..). In an adaptive servoing system was proposed with a look-and-move servoing architecture. The method used optical flow along with SSD to provide a confidence metric and a stochastic controller with Kalman filtering for the control scheme. The system assumes (in the examples) that the plane of the camera and the plane of the features are parallel., discusses an approach of velocity control using the Jacobian relationship s˙ = Jv˙ . In addition the author uses Kalman filtering, assuming that the extracted position of the target have inherent errors (sensor errors). A model of the target velocity is developed and used as a feed-forward input in the control loop. Also, mentions the importance of looking into kinematic discrepancy, dynamic effects, repeatability, settling time oscillations and lag in response. Corke poses a set of very critical questions on visual servoing and tries to elaborate on their implications. The paper primarily focuses the dynamics of visual servoing. The author tries to address problems like lag and stability, while also talking about feed-forward paths in the control loop. The paper also, tries to seek justification for trajectory generation, methodology of axis control and development of performance metrics. Chaumette in provides good insight into the two major problems with IBVS. One, servoing to a local minima and second, reaching a Jacobian singularity. The author show that image points alone do not make good features due to the occurrence of singularities. The paper continues, by discussing the possible additional checks to prevent singularities namely, condition numbers of J_s and Jˆ+_s, to check the null space of ˆ J_s and J^T_s . One main point that the author highlights is the relation between local minima and unrealizable image feature motions. Over the years many hybrid techniques have been developed. These involve computing partial/complete pose from Epipolar Geometry using multiple views or multiple cameras. The values are obtained by direct estimation or through a learning or a statistical scheme. While others have used a switching approach that changes between image-based and position-based on a Lyapnov function. The early hybrid techniques that used a combination of image-based and pose-based (2D and 3D information) approaches for servoing required either a full or partial model of the object in order to extract the pose information and used a variety of techniques to extract the motion information from the image. used an affine motion model from the image motion in addition to a rough polyhedral CAD model to extract the object pose with respect to the camera to be able to servo onto the object (on the lines of PBVS). 2-1/2-D visual servoing developed by Malis et al. is a well known technique that breaks down the information required for servoing into an organized fashion which decouples rotations and translations. The papers assume that the desired pose is known a priori. The rotational information is obtained from partial pose estimation, a homography, (essentially 3D information) giving an axis of rotation and the angle (by computing the eigenvalues and eigenvectors of the homography). The translational information is obtained from the image directly by tracking a set of feature points. The only conditions being that the feature points being tracked never leave the field of view and that a depth estimate be predetermined by some off-line technique. 2-1/2-D servoing has been shown to be more stable than the techniques that preceded it. Another interesting observation with this formulation is that the authors claim that the visual Jacobian will have no singularities during the motions. The hybrid technique developed by Corke and Hutchinson, popularly called portioned approach partitions the visual (or image) Jacobian into motions (both rotations and translations) relating X and Y axes and motions related to the Z axis. outlines the technique, to break out columns of the visual Jacobian that correspond to the Z axis translation and rotation (namely, the third and sixth columns). The partitioned approach is shown to handle the Chaumette Conundrum discussed in. This technique requires a good depth estimate in order to function properly. outlines a hybrid approach where the servoing task is split into two, namely main and secondary. The main task is keep the features of interest within the field of view. While the secondary task is to mark a fixation point and use it as a reference to bring the camera to the desired pose. The technique does need a depth estimate from an off-line procedure. The paper discusses two examples for which depth estimates are obtained from robot odometry and by assuming that all
Read more →
