AI Face Mix

AI Face Mix — independent reviews, comparisons, pricing and step-by-step guides on Aizhi.

• 

  Autognostics

  Autognostics is a new paradigm that describes the capacity for computer networks to be self-aware. It is considered one of the major components of Autonomic Networking. == Introduction == One of the most important characteristics of today's Internet that has contributed to its success is its basic design principle: a simple and transparent core with intelligence at the edges (the so-called "end-to-end principle"). Based on this principle, the network carries data without knowing the characteristics of that data (e.g., voice, video, etc.) - only the end-points have application-specific knowledge. If something goes wrong with the data, only the edge may be able to recognize that since it knows about the application and what the expected behavior is. The core has no information about what should happen with that data - it only forwards packets. Although an effective and beneficial attribute, this design principle has also led to many of today's problems, limitations, and frustrations. Currently, it is almost impossible for most end-users to know why certain network-based applications do not work well and what they need to do to make it better. Also, network operators who interact with the core in low-level terms such as router configuration have problems expressing their high-level goals into low-level actions. In high-level terms, this may be summarized as a weak coupling between the network and application layers of the overall system. As a consequence of the Internet end-to-end principle, the network performance experienced by a particular application is difficult to attribute based on the behavior of the individual elements. At any given moment, the measure of performance between any two points is typically unknown and applications must operate blindly. As a further consequence, changes to the configuration of given element, or changes in the end-to-end path, cannot easily be validated. Optimization and provisioning cannot then be automated except against only the simplest design specifications. There is an increasing interest in Autonomic Networking research, and a strong conviction that an evolution from the current networking status quo is necessary. Although to date there have not been any practical implementations demonstrating the benefits of an effective autonomic networking paradigm, there seems to be a consensus as to the characteristics which such implementations would need to demonstrate. These specifically include continuous monitoring, identifying, diagnosing and fixing problems based on high-level policies and objectives. Autognostics, as a major part of the autonomic networking concept, intends to bring networks to a new level of awareness and eliminate the lack of visibility which currently exists in today's networks. == Definition == Autognostics is a new paradigm that describes the capacity for computer networks to be self-aware, in part and as a whole, and dynamically adapt to the applications running on them by autonomously monitoring, identifying, diagnosing, resolving issues, subsequently verifying that any remediation was successful, and reporting the impact with respect to the application's use (i.e., providing visibility into the changes to networks and their effects). Although similar to the concept of network awareness, i.e., the capability of network devices and applications to be aware of network characteristics (see References section below), it is noteworthy that autognostics takes that concept one step further. The main difference is the auto part of autognostics, which entails that network devices are self-aware of network characteristics, and have the capability to adapt themselves as a result of continuous monitoring and diagnostics. == Path to autognostics == Autognostics, or in other words deep self-knowledge, can be best described as the ability of a network to know itself and the applications that run on it. This knowledge is used to autonomously adapt to dynamic network and application conditions such as utilization, capacity, quality of service/application/user experience, etc. In order to achieve autognosis, networks need a means to: Continuously monitor/test the network for application-specific performance Analyze the monitoring/test data to detect problems (e.g., performance degradation) Diagnose, identify and localize sources of degradation Automatically take actions to resolve problems via remediation/provisioning Verify the problems have been resolved (potentially rolling back changes if ineffective) Subsequently, continue to monitor/test for performance

  Read more →
• 

  Master/Session

  In cryptography, Master/Session is a key management scheme in which a pre-shared Key Encrypting Key (called the "Master" key) is used to encrypt a randomly generated and insecurely communicated Working Key (called the "Session" key). The Working Key is then used for encrypting the data to be exchanged. Its advantage is simplicity, but it suffers the disadvantage of having to communicate the pre-shared Key Exchange Key, which can be difficult to update in the event of compromise. The Master/Session technique was created in the days before asymmetric techniques, such as Diffie-Hellman, were invented. This technique still finds widespread use in the financial industry, and is routinely used between corporate parties such as issuers, acquirers, switches. Its use in device communications (such as PIN pads), however, is in decline given the advantages of techniques such as DUKPT.

  Read more →
• 

  Kerckhoffs's principle

  Kerckhoffs's principle (also called Kerckhoffs's desideratum, assumption, axiom, doctrine or law) of cryptography was stated by the Dutch cryptographer Auguste Kerckhoffs in the 19th century. The principle holds that a cryptosystem should be secure, even if everything about the system, except the key, is public knowledge. This concept is widely embraced by cryptographers, in contrast to security through obscurity, which is not. Kerckhoffs's principle was phrased by the American mathematician Claude Shannon as "the enemy knows the system", i.e., "one ought to design systems under the assumption that the enemy will immediately gain full familiarity with them". In that form, it is called Shannon's maxim. Another formulation by American researcher and professor Steven M. Bellovin is: In other words—design your system assuming that your opponents know it in detail. (A former official at NSA's National Computer Security Center told me that the standard assumption there was that serial number 1 of any new device was delivered to the Kremlin.) == Origins == The invention of telegraphy radically changed military communications and increased the number of messages that needed to be protected from the enemy dramatically, leading to the development of field ciphers which had to be easy to use without large confidential codebooks prone to capture on the battlefield. It was this environment which led to the development of Kerckhoffs's requirements. Auguste Kerckhoffs was a professor of German language at Ecole des Hautes Etudes Commerciales (HEC) in Paris. In early 1883, Kerckhoffs's article, La Cryptographie Militaire, was published in two parts in the Journal of Military Science, in which he stated six design rules for military ciphers. Translated from French, they are: The system must be practically, if not mathematically, indecipherable; It should not require secrecy, and it should not be a problem if it falls into enemy hands; It must be possible to communicate and remember the key without using written notes, and correspondents must be able to change or modify it at will; It must be applicable to telegraph communications; It must be portable, and should not require several persons to handle or operate; Lastly, given the circumstances in which it is to be used, the system must be easy to use and should not be stressful to use or require its users to know and comply with a long list of rules. Some are no longer relevant given the ability of computers to perform complex encryption. The second rule, now known as Kerckhoffs's principle, is still critically important. == Explanation of the principle == Kerckhoffs viewed cryptography as a rival to, and a better alternative than, steganographic encoding, which was common in the nineteenth century for hiding the meaning of military messages. One problem with encoding schemes is that they rely on humanly-held secrets such as "dictionaries" which disclose for example, the secret meaning of words. Steganographic-like dictionaries, once revealed, permanently compromise a corresponding encoding system. Another problem is that the risk of exposure increases as the number of users holding the secrets increases. Nineteenth century cryptography, in contrast, used simple tables which provided for the transposition of alphanumeric characters, generally given row-column intersections which could be modified by keys which were generally short, numeric, and could be committed to human memory. The system was considered "indecipherable" because tables and keys do not convey meaning by themselves. Secret messages can be compromised only if a matching set of table, key, and message falls into enemy hands in a relevant time frame. Kerckhoffs viewed tactical messages as only having a few hours of relevance. Systems are not necessarily compromised, because their components (i.e. alphanumeric character tables and keys) can be easily changed. === Advantage of secret keys === Using secure cryptography is supposed to replace the difficult problem of keeping messages secure with a much more manageable one, keeping relatively small keys secure. A system that requires long-term secrecy for something as large and complex as the whole design of a cryptographic system obviously cannot achieve that goal. It only replaces one hard problem with another. However, if a system is secure even when the enemy knows everything except the key, then all that is needed is to manage keeping the keys secret. There are a large number of ways the internal details of a widely used system could be discovered. The most obvious is that someone could bribe, blackmail, or otherwise threaten staff or customers into explaining the system. In war, for example, one side will probably capture some equipment and people from the other side. Each side will also use spies to gather information. If a method involves software, someone could do memory dumps or run the software under the control of a debugger in order to understand the method. If hardware is being used, someone could buy or steal some of the hardware and build whatever programs or gadgets needed to test it. Hardware can also be dismantled so that the chip details can be examined under the microscope. === Maintaining security === A generalization some make from Kerckhoffs's principle is: "The fewer and simpler the secrets that one must keep to ensure system security, the easier it is to maintain system security." Bruce Schneier ties it in with a belief that all security systems must be designed to fail as gracefully as possible: Kerckhoffs's principle applies beyond codes and ciphers to security systems in general: every secret creates a potential failure point. Secrecy, in other words, is a prime cause of brittleness—and therefore something likely to make a system prone to catastrophic collapse. Conversely, openness provides ductility. Any security system depends crucially on keeping some things secret. However, Kerckhoffs's principle points out that the things kept secret ought to be those least costly to change if inadvertently disclosed. For example, a cryptographic algorithm may be implemented by hardware and software that is widely distributed among users. If security depends on keeping that secret, then disclosure leads to major logistic difficulties in developing, testing, and distributing implementations of a new algorithm – it is "brittle". On the other hand, if keeping the algorithm secret is not important, but only the keys used with the algorithm must be secret, then disclosure of the keys simply requires the simpler, less costly process of generating and distributing new keys. == Applications == In accordance with Kerckhoffs's principle, the majority of civilian cryptography makes use of publicly known algorithms. By contrast, ciphers used to protect classified government or military information are often kept secret (see Type 1 encryption). However, it should not be assumed that government/military ciphers must be kept secret to maintain security. It is possible that they are intended to be as cryptographically sound as public algorithms, and the decision to keep them secret is in keeping with a layered security posture. == Security through obscurity == It is moderately common for companies to keep the inner workings of a system secret. Some argue this "security by obscurity" makes the product safer and less vulnerable to attack. A counter-argument is that keeping the innards secret may improve security in the short term, but in the long run, only systems that have been published and analyzed should be trusted. Steven Bellovin and Randy Bush commented: Security Through Obscurity Considered Dangerous Hiding security vulnerabilities in algorithms, software, and/or hardware decreases the likelihood they will be repaired and increases the likelihood that they can and will be exploited. Discouraging or outlawing discussion of weaknesses and vulnerabilities is extremely dangerous and deleterious to the security of computer systems, the network, and its citizens. Open Discussion Encourages Better Security The long history of cryptography and cryptoanalysis has shown time and time again that open discussion and analysis of algorithms exposes weaknesses not thought of by the original authors, and thereby leads to better and more secure algorithms. As Kerckhoffs noted about cipher systems in 1883 [Kerc83], "Il faut qu'il n'exige pas le secret, et qu'il puisse sans inconvénient tomber entre les mains de l'ennemi." (Roughly, "the system must not require secrecy and must be able to be stolen by the enemy without causing trouble.")

  Read more →
• 

  Trust federation

  A trust federation is part of the evolving Identity Metasystem that will bring a new layer of persistent identity and trusted data sharing to the Internet. Although the concept of trust federations is technology neutral, several protocols like SAML, OpenID, Information Card, XDI can handle the challenges of technical interoperability. The challenge of business and social interoperability requires a new type of cooperative association similar to a credit card association. Instead of banks, however, a trust federation is an alliance of i-brokers and their customers who agree to abide by a common set of agreements in the care and handling of customer data. A model for trust federations is offered by Open Identity Exchange and Kantara Initiative, which is applied in the U.S. Government ICAM Trust Framework. Some operational trust federations are: InCommon (academic, USA) REFEDs (Research and Education Federations, Europe) IGTF Interoperable Global Trust Federation Portalverbund Government Portal Federation, Austria Trust federations are not limited to the social web use case, but apply to all federations where trust in identity and compliance to other objectives of information security such as confidentiality, integrity and privacy is brokered.

  Read more →
• 

  VGACAD

  VGACAD was the parent of a suite of shareware graphic utilities made for the MS-DOS operating system used in the IBM PC and clones. It was popular for editing and capturing images using BSAVE (graphics image format) and provided an early graphic editing suite compatible with multiple graphic cards and resolutions, used on the IBM PC. == Usage == Written by Lawrence Gozum in 1987, it was the genesis of multiple versions and improvements over 10 years. Ran with his brother, Marvin initially helped with design ideas, strategic focus, technical support calls, and managing the early shareware business. The growth of the VGACAD suite grew quickly to preoccupy most of their time. Lawrence then focused more of his efforts on software and formed Applied Insights, to manage VGACAD and its offspring, VidFun, and Ai Picture Explorer. At its peak, its users ranged from individuals, Federal government offices, museums and major newspapers. == Features == VGACAD was a misnomer, and meant VGA-Computer Assisted Drawing, rather than computer-aided design, as CAD is commonly referred to today. Its longevity was due to its color accuracy, speed, small size, and that its suite of small utilities often worked stand-alone. One called VGACAP, for 'capture', dumped video memory into a file that could later be converted to popular graphic image formats, later made commonplace when Microsoft Windows programmed the print screen key to dump graphics into the clipboard. However, VGACAP ran insulated apart from early versions of Windows, and thus could capture screens were applications prohibited such function.

  Read more →
• 

  Group key

  In cryptography, a group key is a cryptographic key that is shared between a group of users. Typically, group keys are distributed by sending them to individual users, either physically, or encrypted individually for each user using either that user's pre-distributed private key. A common use of group keys is to allow a group of users to decrypt a broadcast message that is intended for that entire group of users, and no one else. For example, in the Second World War, group keys (known as "iodoforms", a term invented by a classically educated non-chemist, and nothing to do with the chemical of the same name) were sent to groups of agents by the Special Operations Executive. These group keys allowed all the agents in a particular group to receive a single coded message. In present-day applications, group keys are commonly used in conditional access systems, where the key is the common key used to decrypt the broadcast signal, and the group in question is the group of all paying subscribers. In this case, the group key is typically distributed to the subscribers' receivers using a combination of a physically distributed secure cryptoprocessor in the form of a smartcard and encrypted over-the-air messages.

  Read more →
• 

  Death of Molly Russell

  In November 2017, Molly Russell, a fourteen-year-old British schoolgirl from Harrow, London, was found dead in her bedroom by her parents. In an inquest, the coroner stated that she had died from an act of self-harm following depression and the results of social media consumption, including material on Instagram and Pinterest. She also had a Twitter account in which she documented her growing depression. == Life == Russell had been a pupil at Hatch End High School. At the inquest, the school's head teacher expressed shock that she was able to access distressing online content. Her parents stated that she had never shown any previous signs of struggle and was doing very well in school. It was revealed at the inquest that in the six months prior to her death, 2,100 of 16,300 pieces of content she had interacted with on Instagram were on topics such as self-harm, depression, and suicide. It was also noted that throughout her experience on social media, there were never any warning signs about the information she viewed on these platforms. == Subsequent events == Dr. Navin Venugopal, the child psychiatrist assigned to the case investigating her death, called the material she viewed "disturbing and distressing" and said he was unable to sleep well for weeks after viewing it. The coroner Andrew Walker concluded that Molly's death was "an act of self harm suffering from depression and the negative effects of online content". He issued a prevention of future deaths report regarding her death, in which he made a number of recommendations for operators of online platforms, including: separating platforms for adults and children age verification changes in policy on filtering of age-specific content adding features for parental supervision and control data retention of material viewed by children He suggested that this could be accomplished by either legislation or self-regulation. The lawyer representing her family at the inquest stated that the findings "captured all of the elements of why this material is so harmful." The case has been cited as a motivator for the passage of the Online Safety Act. A charity, the Molly Rose Foundation, was set up in her memory, with the goal of suicide prevention for young people. Meta and Pinterest are believed to have made substantial donations to the charity.

  Read more →
• 

  G.hn

  Gigabit Home Networking (G.hn) is a specification for wired home networking that supports speeds up to 2 Gbit/s and operates over four types of legacy wires: telephone wiring, coaxial cables, power lines and plastic optical fiber. Some benefits of a multi-wire standard are lower equipment development costs and lower deployment costs for service providers (by allowing customer self-install). == History == G.hn was developed under the International Telecommunication Union's Telecommunication Standardization sector (the ITU-T) and promoted by the HomeGrid Forum and several other organizations. ITU-T Recommendation (the ITU's term for standard) G.9960, which received approval on October 9, 2009, specified the physical layers and the architecture of G.hn. The Data Link Layer (Recommendation G.9961) was approved on June 11, 2010. Prominent organizations, including CEPca, HomePNA, and UPA, who were creators of some of these interfaces, rallied behind the latest version of the standard, emphasizing its potential and significance in the home networking domain. Moreover, the ITU-T extended the technology with multiple input, multiple output (MIMO) technology to increase data rates and signaling distance. This new feature was approved in March 2012 under G.9963 Recommendation. The development and promotion of G.hn have been significantly supported by the HomeGrid Forum and several other organizations. The technology was not only designed to address home-networking challenges but also found applications beyond this initial scope, showcasing its versatility and potential in the networking domain. == Technical specifications == === Technical overview === G.hn specifies a single physical layer based on fast Fourier transform (FFT) orthogonal frequency-division multiplexing (OFDM) modulation and low-density parity-check code (LDPC) forward error correction (FEC) code. G.hn includes the capability to notch specific frequency bands to avoid interference with amateur radio bands and other licensed radio services. G.hn includes mechanisms to avoid interference with legacy home networking technologies and also with other wireline systems such as VDSL2 or other types of DSL used to access the home. OFDM systems split the transmitted signal into multiple orthogonal sub-carriers. In G.hn each one of the sub-carriers is modulated using QAM. The maximum QAM constellation supported by G.hn is 4096-QAM (12-bit QAM). The G.hn media access control is based on a time division multiple access (TDMA) architecture, in which a "domain master" schedules Transmission Opportunities (TXOPs) that can be used by one or more devices in the "domain". There are two types of TXOPs: Contention-Free Transmission Opportunities (CFTXOP), which have a fixed duration and are allocated to a specific pair of transmitter and receiver. CFTXOP are used for implementing TDMA Channel Access for specific applications that require quality of service (QoS) guarantees. Shared Transmission Opportunities (STXOP), which are shared among multiple devices in the network. STXOP are divided into Time Slots (TS). There are two types of TS: Contention-Free Time Slots (CFTS), which are used for implementing "implicit" token passing Channel Access. In G.hn, a series of consecutive CFTS is allocated to a number of devices. The allocation is performed by the "domain master" and broadcast to all nodes in the network. There are pre-defined rules that specify which device can transmit after another device has finished using the channel. As all devices know "who is next", there is no need to explicitly send a "token" between devices. The process of "passing the token" is implicit and ensures that there are no collisions during Channel access. Contention-Based Time Slots (CBTS), which are used for implementing CSMA/CARP Channel Access. In general, CSMA systems cannot completely avoid collisions, so CBTS are only useful for applications that do not have strict Quality of Service requirements. ==== Optimization for each medium ==== Although most elements of G.hn are common for all three media supported by the standard (power lines, phone lines and coaxial cable), G.hn includes media-specific optimizations for each media. Some of these media-specific parameters include: OFDM Carrier Spacing: 195.31 kHz in coaxial, 48.82 kHz in phone lines, 24.41 kHz in power lines. FEC Rates: G.hn's FEC can operate with code rates 1/2, 2/3, 5/6, 16/18 and 20/21. Although these rates are not media specific, it is expected that the higher code rates will be used in cleaner media (such as coaxial) while the lower code rates will be used in noisy environments such as power lines. Automatic repeat request (ARQ) mechanisms: G.hn supports operation both with and without ARQ (re-transmission). Although this is not media specific, it is expected that ARQ-less operation is sometimes appropriate for cleaner media (such as coaxial) while ARQ operation is appropriate for noisy environments such as power lines. Power levels and frequency bands: G.hn defines different power masks for each medium. MIMO support: Recommendation G.9963 includes provisions for transmitting G.hn signals over multiple AC wires (phase, neutral, ground), if they are physically available. In July 2016, G.9963 was updated to include MIMO support over twisted pairs. ==== Security ==== G.hn uses the Advanced Encryption Standard (AES) encryption algorithm (with a 128-bit key length) using the CCMP protocol to ensure confidentiality and message integrity. Authentication and key exchange is done following ITU-T Recommendation X.1035. G.hn specifies point-to-point security inside a domain, which means that each pair of transmitter and receiver uses a unique encryption key which is not shared by other devices in the same domain. For example, if node Alice sends data to node Bob, node Eve (in the same domain as Alice and Bob) will not be able to easily eavesdrop their communication. G.hn supports the concept of relays, in which one device can receive a message from one node and deliver it to another node farther away in the same domain. Relaying becomes critical for applications with complex network topologies that need to cover large distances, such as those found in industrial or utility applications. While a relay can read the source and target addresses, it cannot read the message's content due to its body being end-to-end-encrypted. ==== Profiles ==== The G.hn architecture includes the concept of profiles. Profiles are intended to address G.hn nodes with significantly different levels of complexity. In G.hn the higher complexity profiles are proper supersets of lower complexity profiles, so that devices based on different profiles can interoperate with each other. Examples of G.hn devices based on high complexity profiles are Residential Gateways or Set-Top Boxes. Examples of G.hn devices based on low complexity profiles are home automation, home security and smart grid devices. ==== Technical parameters ==== The chart depicts a summary of the crucial technical specifications of the G.hn standard. Many of these technical elements are consistent across different physical media, with variations seen in areas such as Tone Spacing and frequency ranges. This uniformity is essential as it allows silicon manufacturers to produce a singular chip capable of implementing all three media types, leading to cost savings. Presently, G.hn chipsets are compatible with all three media types. This compatibility allows system manufacturers to create devices that can adjust to any wiring type simply by modifying a software configuration in the equipment. === Spectrum === The G.hn spectrum depends on the medium as shown in the diagram below: === Protocol stack === G.hn specifies the physical layer and the data link layer, according to the OSI model. The G.hn Data Link Layer (Recommendation G.9961) is divided into three sub-layers: The Application Protocol Convergence (APC) Layer, which accepts frames (usually in Ethernet format) from the upper layer (Application Entity) and encapsulates them into G.hn APC protocol data units (APDUs). The maximum payload of each APDU is 214 bytes. The logical link control (LLC), which is responsible for encryption, aggregation, segmentation and automatic repeat-request. This sub-layer is also responsible for "relaying" of APDUs between nodes that may not be able to communicate through a direct connection. The medium access control (MAC), which schedules channel access. The G.hn physical layer (Recommendation G.9960) is divided into three sub-layers: The Physical Coding Sub-layer (PCS), responsible for generating PHY headers. The Physical Medium Attachment (PMA), responsible for scrambling and forward error correction coding/decoding. The Physical Medium Dependent (PMD), responsible for bit-loading and OFDM modulation. The interface between the Application Entity and the Data Link Layer is called A-interface. The interface between the Data Link Layer and the ph

  Read more →
• 

  Research software engineering

  Research software engineering is the application of software engineering practices, methods and techniques for research software, i.e. software that was made for and is mainly used within research projects. As usual for software engineering, this also includes knowledge of other (and in this case varying) research fields as well as open science that need to be incorporated into a software development process. The term was proposed in a research paper in 2010 in response to an empirical survey on tools used for software development in research projects. It started to be used in United Kingdom in 2012, when it was needed to define the type of software development needed in research. This focuses on reproducibility, reusability, and accuracy of data analysis and applications created for research. == Support == Various type of associations and organisations have been created around this role to support the creation of posts in universities and research institutes. In 2014 a Research Software Engineer Association was created in UK, which attracted 160 members in the first three months and which lead to the creation of the Society of Research Software Engineering in 2019. Other countries like the Netherlands, Germany, and the USA followed creating similar communities and there are similar efforts being pursued in Asia, Australia, Canada, New Zealand, the Nordic countries, and Belgium. In January 2021 the International Council of RSE Associations was introduced. UK counts over 40 universities and institutes with groups that provide access to software expertise to different areas of research. Additionally, the Engineering and Physical Sciences Research Council created a Research Software Engineer fellowship to promote this role and help the creation of RSE groups across UK, with calls in 2015, 2017, and 2020. The world first RSE conference took place in UK in September 2016 and it has been repeated annually (except for a gap in 2020) since. In 2019 the first national RSE conferences in Germany and the Netherlands were held, next editions were planned for 2020 and then cancelled. US-RSE held its first national conference in 2023. The Research Software Alliance was formed in 2019 to advance the global research software ecosystem by collaborating with decision makers and key influencers. The SORSE (A Series of Online Research Software Events) community was established in late‑2020 in response to the COVID-19 pandemic and ran its first online event in September 2020.

  Read more →
• 

  Internet Security Alliance

  Internet Security Alliance (ISA) was founded in 2001 as a non-profit collaboration between Carnegie Mellon University's CyLab and Electronic Industries Alliance, a federation of trade associations. The Internet Security Alliance is focused on cyber security, acting as a forum for information sharing and leadership on information security, and lobbying for corporate security interests. == International operations == The Internet Security Alliance operates with a global membership to provide international security for its partners. The organization's membership includes companies located on four continents, and the Executive Committee always includes at least one non-U.S.-based company. The Internet Security Alliance believes that international communication is crucial for long-term greater information security, as it allows for a more realistic approach to addressing the many challenges faced by users of the Internet. == Publications == Published in 2009, The Financial Impact of Cyber Risk is the first known guidance document to attempt to approach the financial impact of cyber risks from the perspective of core business functions. It claims to provide guidance to CFOs and their colleagues responsible for legal issues, business operations and technology, privacy and compliance, risk assessment and insurance, and corporate communications.

  Read more →
• 

  Electronic lab notebook

  An electronic lab notebook or electronic laboratory notebook (ELN) is a computer program designed to replace paper laboratory notebooks. Lab notebooks in general are used by scientists, engineers, and technicians to document research, experiments, and procedures performed in a laboratory. A lab notebook is often maintained to be a legal document and may be used in a court of law as evidence. Similar to an inventor's notebook, the lab notebook is also often referred to in patent prosecution and intellectual property litigation. Electronic lab notebooks offer many benefits to the user as well as organizations; they are easier to search upon, simplify data copying and backups, and support collaboration amongst many users. ELNs can have fine-grained access controls, and can be more secure than their paper counterparts. They also allow the direct incorporation of data from instruments, replacing the practice of printing out data to be stapled into a paper notebook. == Types == ELNs can be divided into two categories: "Specific ELNs" contain features designed to work with specific applications, scientific instrumentation or data types. "Cross-disciplinary ELNs" or "Generic ELNs" are designed to support access to all data and information that needs to be recorded in a lab notebook. Lab Platforms that combine an ELN, LIMS, and scientific data management together, all-in-one configurable software environment. Solutions range from specialized programs designed from the ground up for use as an ELN, to modifications or direct use of more general programs. Examples of using more general software as an ELN include using OpenWetWare, a MediaWiki install (running the same software that Wikipedia uses), WordPress, or the use of general note taking software such as OneNote as an ELN. ELN's come in many different forms. They can be standalone programs, use a client-server model, or be entirely web-based. Some use a lab-notebook approach, others resemble a blog. ELNs are embracing artificial intelligence and LLM technology to provide scientific AI chat assistants. A good many variations on the "ELN" acronym have appeared. Differences between systems with different names are often subtle, with considerable functional overlap between them. Examples include "ERN" (Electronic Research Notebook), "ERMS" (Electronic Resource (or Research or Records) Management System (or Software) and SDMS (Scientific Data (or Document) Management System (or Software). Ultimately, these types of systems all strive to do the same thing: Capture, record, centralize and protect scientific data in a way that is highly searchable, historically accurate, and legally stringent, and which also promotes secure collaboration, greater efficiency, reduced mistakes and lowered total research costs. == Objectives == A good electronic laboratory notebook should offer a secure environment to protect the integrity of both data and process, whilst also affording the flexibility to adopt new processes or changes to existing processes without recourse to further software development. The package architecture should be a modular design, so as to offer the benefit of minimizing validation costs of any subsequent changes that you may wish to make in the future as your needs change. A good electronic laboratory notebook should be an "out of the box" solution that, as standard, has fully configurable forms to comply with the requirements of regulated analytical groups through to a sophisticated ELN for inclusion of structures, spectra, chromatograms, pictures, text, etc. where a preconfigured form is less appropriate. All data within the system may be stored in a database (e.g. MySQL, MS-SQL, Oracle) and be fully searchable. The system should enable data to be collected, stored and retrieved through any combination of forms or ELN that best meets the requirements of the user. The application should enable secure forms to be generated that accept laboratory data input via PCs and/or laptops / palmtops, and should be directly linked to electronic devices such as laboratory balances, pH meters, etc. Networked or wireless communications should be accommodated for by the package which will allow data to be interrogated, tabulated, checked, approved, stored and archived to comply with the latest regulatory guidance and legislation. A system should also include a scheduling option for routine procedures such as equipment qualification and study related timelines. It should include configurable qualification requirements to automatically verify that instruments have been cleaned and calibrated within a specified time period, that reagents have been quality-checked and have not expired, and that workers are trained and authorized to use the equipment and perform the procedures. == Regulatory and legal aspects == The laboratory accreditation criteria found in the ISO 17025 standard needs to be considered for the protection and computer backup of electronic records. These criteria can be found specifically in clause 4.13.1.4 of the standard. Electronic lab notebooks used for development or research in regulated industries, such as medical devices or pharmaceuticals, are expected to comply with FDA regulations related to software validation. The purpose of the regulations is to ensure the integrity of the entries in terms of time, authorship, and content. Unlike ELNs for patent protection, FDA is not concerned with patent interference proceedings, but is concerned with avoidance of falsification. Typical provisions related to software validation are included in the medical device regulations at 21 CFR 820 (et seq.) and Title 21 CFR Part 11. Essentially, the requirements are that the software has been designed and implemented to be suitable for its intended purposes. Evidence to show that this is the case is often provided by a Software Requirements Specification (SRS) setting forth the intended uses and the needs that the ELN will meet; one or more testing protocols that, when followed, demonstrate that the ELN meets the requirements of the specification and that the requirements are satisfied under worst-case conditions. Security, audit trails, prevention of unauthorized changes without substantial collusion of otherwise independent personnel (i.e., those having no interest in the content of the ELN such as independent quality unit personnel) and similar tests are fundamental. Finally, one or more reports demonstrating the results of the testing in accordance with the predefined protocols are required prior to release of the ELN software for use. If the reports show that the software failed to satisfy any of the SRS requirements, then corrective and preventive action ("CAPA") must be undertaken and documented. Such CAPA may extend to minor software revisions, or changes in architecture or major revisions. CAPA activities need to be documented as well. Aside from the requirements to follow such steps for regulated industry, such an approach is generally a good practice in terms of development and release of any software to assure its quality and fitness for use. There are standards related to software development and testing that can be applied (see ref.).

  Read more →
• 

  Data security

  Data security or data protection is the process of securing digital information to protect it from online threats. Data security or protection means protecting digital data, such as those in a database, from destructive forces and from the unwanted actions of unauthorized users, such as a cyberattack or a data breach. Data security protects computer hardware, software, storage devices, and the data of user devices. Data security also protects the data of organizations, companies and administrative controls. Data security guarantees the protection of individual data, such as identity documents and bank data, and protects against unauthorized access, theft and loss of individual data. Data security also protects data breaches that occurs in companies and industries. Good security measures in industries reduce the probability of data breaches, and employees can rely on the company with their data and private information to be kept secured while companies can continue to maintain a stable reputation. The CIA Triad (Confidentiality, Integrity, and Availability) is what is used to practice what an information security is required to follow. Confidentiality, protects information from being accessed by unauthorized persons. Integrity, makes sure data is trustworthy; and Availability, meaning that data can be accessed by approved users when it is needed; are three goals for data security. Non-repudiation in data security definition, is a device/service that shows where the data originated from and the proof of integrity. == Technologies == === Disk encryption === Disk encryption refers to encryption technology that encrypts data on a hard disk drive. It takes data from a storage device and coverts it into an unreadable format. Disk encryption typically takes form in either software (see disk encryption software) or hardware (see disk encryption hardware) which can be used together. Disk encryption is often referred to as on-the-fly encryption (OTFE) or transparent encryption. Full disk encryption encrypts each individual sector of a disk volume. Files and user data are encrypted to hinder unauthorized users from accessing without a decryption key. A diversifier permits a plaintext of a specific disk sector to be encrypted into different ciphertexts, which does not require additional storage, such as an initialization vector (IV) or message authentication code (MAC). === Software versus hardware-based mechanisms for protecting data === Software-based security solutions encrypt the data to protect it from theft. However, a malicious program or a hacker could corrupt the data to make it unrecoverable, making the system unusable. Hardware-based security solutions prevent read and write access to data, which provides very strong protection against tampering and unauthorized access. Hardware-based security or assisted computer security offers an alternative to software-only computer security. Security tokens such as those using PKCS#11 or a mobile phone may be more secure due to the physical access required in order to be compromised. Access is enabled only when the token is connected and the correct PIN is entered (see two-factor authentication). However, dongles can be used by anyone who can gain physical access to it. Newer technologies in hardware-based security solve this problem by offering full proof of security for data. Working off hardware-based security: A hardware device allows a user to log in, log out and set different levels through manual actions. Many devices use biometric technology to prevent malicious users from logging in, logging out, and changing privilege levels. The current state of a user of the device is read by controllers in peripheral devices such as hard disks. Illegal access by a malicious user or a malicious program is interrupted based on the current state of a user by hard disk and DVD controllers making illegal access to data impossible. Hardware-based access control is more secure than the protection provided by the operating systems as operating systems are vulnerable to malicious attacks by viruses and hackers. The data on hard disks can be corrupted after malicious access is obtained. With hardware-based protection, the software cannot manipulate the user privilege levels. A hacker or a malicious program cannot gain access to secure data protected by hardware or perform unauthorized privileged operations. This assumption is broken only if the hardware itself is malicious or contains a backdoor. The hardware protects the operating system image and file system privileges from being tampered with. Therefore, a completely secure system can be created using a combination of hardware-based security and secure system administration policies. === Backups === Backup is the process of reproducing copies of essential data and storing in a separate, secured place. It is used to ensure data that is lost can be recovered from another source. Backups contains a minimum of one copy of the data that requires preservation. It is considered essential to keep a backup of any data in most industries and the process is recommended for any files of importance to a user. There are 3 types of backups; full backups, incremental backups, and differential backups. Full backups secure all data from a production system, such as a server, database, or other connected data source. It is impossible to lose all data in a full backup if a breach or corruption were to occur. Full backups require a significantly large amount of time to back up and may be time-consuming taking hours to days to complete. Incremental backups only secures changed data since last backup. While all backups are done in full backups, incremental backups only save data that is recently or frequently changed. Incremental backups require lower storage costs making it a prominent solution for growing datasets. === Data Privacy === Data privacy (or information privacy) is the right for individual's data to be secured to obstruct the use of unauthorized access. It gives individuals control over their data and how it can be shared to third parties. The U.S Privacy Protection Law (see Privacy laws of the United States) requires organizations to inform individuals of how their data is collected and when a data breach occurs. By implementing an encryption, it ensures that private data is unreadable to cybercriminals. === Data masking === Data masking of structured data is the process of obscuring (masking) specific data within a database table or cell to ensure that data security is maintained and sensitive information is not exposed to unauthorized personnel. This may include masking the data from users (for example so banking customer representatives can only see the last four digits of a customer's national identity number), developers (who need real production data to test new software releases but should not be able to see sensitive financial data), outsourcing vendors, etc. Data masking is a form of encryption, as it obscures data by modifying particular letters and numbers to keep data concealed and protected from potential hackers. The individual that has access to the code that decrypts the replaced characters are the only ones that can uncover the data. === Data erasure === Data erasure (or data deletion, data destruction) is a method of software-based overwriting that permanently clears all electronic data residing on a hard drive or other digital media to ensure that no sensitive data is lost when an asset is retired or reused. Article 17: Right to be Forgotten states that users have the right to permanently remove all of their private information from their old devices/services to give people more control over their data. Users are able to switch between devices efficiently. == Threats == === Malware === Malware (or malicious software) is designed to destroy, corrupt or gain unauthorized access to a computer for the purpose of stealing, or destroying data. Hackers who use malware typically utilize many types of malware, which includes computer virus, computer worms, ransomware, spyware and Trojan horse to create a vast system of disruption and cause easy data theft. One of the victims of the vast system of disruption includes healthcare workers, who are targeted by compromised systems by infections and then having their data attacked. === Phishing === Phishing is a type of scam that allows hackers to hoax people using psychological and social engineering (using human emotions such as their trust and fear) tactics into giving personal data through emails and messages, and install computer viruses if the individual were to click on a malicious link unknowingly. Attackers are able to create websites that are very similar to original websites, which makes it difficult to detect a fake website, causing individuals to fall for giving in information. Phishing attackers use human emotion to exploit them, such as making them feel fear, urgency, sympathy with the message

  Read more →
• 

  Fuse Services Framework

  Fuse Services Framework is an open source SOAP and REST web services platform based on Apache CXF for use in enterprise IT organizations. It is productized and supported by the Fuse group at FuseSource Corp. Fuse Services Framework service-enables new and existing systems for use in enterprise SOA infrastructure. Fuse Services Framework is a pluggable, small-footprint engine that creates high performance, secure and robust services in minutes using front-end programming APIs like JAX-WS and JAX-RS. It supports multiple transports and bindings and is extensible so developers can add bindings for additional message formats so all systems can work together without having to communicate through a centralized server. Fuse Services Framework is now a part of Red Hat JBoss Fuse. Fabric8 is a free Apache 2.0 Licensed upstream community for the JBoss Fuse product from Red Hat.

  Read more →
• 

  Key Transparency

  Key Transparency allows communicating parties to verify public keys used in end-to-end encryption. In many end-to-end encryption services, to initiate communication a user will reach out to a central server and request the public keys of the user with which they wish to communicate. If the central server is malicious or becomes compromised, a man-in-the-middle attack can be launched through the issuance of incorrect public keys. The communications can then be intercepted and manipulated. Additionally, legal pressure could be applied by surveillance agencies to manipulate public keys and read messages. With Key Transparency, public keys are posted to a public log that can be universally audited. Communicating parties can verify public keys used are accurate.

  Read more →
• 

  Defence Information Infrastructure

  Defence Information Infrastructure (DII) is a secure military network owned by the United Kingdom's Ministry of Defence MOD. It is used by all branches of the armed forces, including the Royal Navy, British Army and Royal Air Force as well as MOD civil servants. It reaches to deployed bases and ships at sea, but not to aircraft in flight. In 2000, the MOD began to plan the systems replacement project. In March 2005, the MOD gave a contract to the Atlas Consortium, with EDS as prime contractor, for installation and management over 10 years. That has developed into a consortium made up of DXC Technology (formerly EDS), Fujitsu, Airbus Defence and Space (formerly EADS Defence & Security) and CGI (formerly Logica). Starting in May 2016, MOD users of DII begin to migrate to the New Style of IT within the defence to be known as MODNET; again supported by ATLAS. == Overview == DII supports 2,000 MOD sites with some 150,000 terminals (desktops and laptops) and 300,000 user accounts. It is designed to offer a high level of resilience, flexibility, and security in the provision of connectivity from ‘business space to battlespace’ in MOD offices in the UK, bases overseas, at sea, and on the front line. It aims to rationalise and improve IT provision for the defence sector in the 21st century; involving a major culture change for MOD users and their ways of working through a structure of shared working areas with controlled security and access. It should provide a records management system and search facility together with a range of office services. It hosts several hundred COTS (commercial off-the-shelf) and bespoke MOD applications from a range of suppliers judged to meet the required security standards. The network handles alphanumeric data, graphics, and video. The system carries information from Restricted to above-Secret levels, but users are able to see only the data and applications for which they are authorised. == Incremental approach == In order to de-risk the programme Atlas and the MOD took an incremental approach to the development and implementation of DII, with a separate contract for each increment. The extended timeline allowed the MOD flexibility in defining its requirements. Increment 1: Contract awarded March 2005. This covered 70,000 user access devices (UADs) and 200,000 user accounts in the Restricted and Secret domains in 680 fixed locations. Increment 2a: Contract awarded December 2006. This was for an additional 44,000 UADs and 58,000 user accounts in the Restricted and Secret domains, again in fixed locations. Increment 2b: Contract awarded September 2007: This extended DII(F) into the deployed environment with the provision of UADs to support land and maritime deployed operations. Increment 2c: Signed in January 2009. This extended the DII footprint into the above-Secret domain to support a number of key operations and intelligence initiatives. Increment 3a: Contract awarded January 2010. Atlas provided 42,000 UADs operating in the Restricted and Secret domains to the remaining MOD fixed sites. This supported some 60,000 personnel, notably within the RAF, at Joint Helicopter Command and other MOD locations. Increment 3a received an MOD Chief of Defence Materiel commendation. == Costs and transparency == The Ministry of Defence informed Parliament the system would cost £2.3bn, even though it knew the cost would be at least £5.8bn. By 2008 the programme was running at least 18 months late; had delivered only 29,000 of a contracted 63,000 terminals; and had delivered none of the contracted Secret capability. In January 2010 the Parliamentary Under-Secretary of State for Defence announced that the Ministry of Defence had authorised DII increment 3a at a cost of around £540 million to provide 42,000 terminals within the RAF and at Joint Helicopter Command. He stated that the project would deliver "benefits" worth over £1.6 billion over the 10 years of the contract. That year the project was scheduled to cost at least £7bn, however, the UK government said it might attempt to reduce this sum. By 2014 the rollout of all UK terminals was complete and a refresh of the original desktops and printers to new hardware underway. The overseas rollout was coming to an end and well over half the fleet, including aircraft carrier HMS Queen Elizabeth, equipped. The final part of Secret capability deployment was scheduled to complete in summer of 2014.

  Read more →